Recent: Fix food processor motor?

Mend Document Laminators

Office Appliances, Document Laminators howtomendit.com find out how to mend just about anything.
Categories

Mend Ultima 65

Free repair help

We have 58 questions about mending 'ultima 65' in category Office Appliances, Document Laminators

How to mend ... Ultima 65

Pages 321
Mend gbc 65 heat

our GBC Ultima 65 control panel is not on?

Our GBC Ultima 65 control panel is not on. The laminate frolled into the heat rollers and the control panel ... [Read more]
Mend power switch burned

GBC Ultima 65 Power Switch Failure?

The AC Switch on my Ultima 65 burned out/melted. I replaced the switch and that one melted, too. What would ... [Read more]
Mend plug power motor

how can i fix my lamintor?

how can I fix my ultima 65 laminator? ...I plug it in and the power wont go on....is the motor shot?
Mend comes while shuts

Laminator comes on for a while and then shuts down?

GBC Ultima 65 laminator comes on and seems to be warming up and then trips circuit breaker never reaching temp... [Read more]
Mend gbc ultima 65

GBC Ultima 65 Doesn't heat up?

We've replaced the coils and the circuit breaker. Finally checked for power. We have current going into the ... [Read more]
Mend ultima over heating

Ultima 65 over heating?

Ultima 65 ready light never shows ready, it continues to blink, but the laminator is getting very hot, too hot... [Read more]
Mend Office Appliances, Document Laminators

Ultima 65 Can't get poles off?

We cannot get the poles off that hold the laminating paper. It says to move it to the right and then pull out ... [Read more]
Mend 65 light not turning

GBC Ultima 65 ready light not turning on?

Hi, Our GBC Ultima 65 laminator stays on wait light continually. The ready light will not come on, however... [Read more]
Mend gbc ultima 65 laminator

GBC Ultima 65 Laminator?

Laminator runs fine for about 2-3 feet of lamination, then just stops-power is on, heat is on, rollers just st... [Read more]
Mend heat ultima 65

Heat roller Ultima 65 Bob Haller you out there???

Bob I have another Ultima 65 that has a heat roller swollen in the middle. (apparently My name is getting arou... [Read more]
Mend ultima put t

Ultima 65 Laminator. I put 27" film and now can't get it out?

I put the 27" film on the rod and it was hard to get into the machine. Now I can't get it out.
Mend gbc ultima 65 problem

GBC Ultima 65 problem?

GBC Ultima 65 I repair these, but I don't see too many I only know of 3 in Dublin, however I have one that's s... [Read more]
Mend gbc ultima 65 laminator

GBC Ultima 65 laminator roller not heating?

Hi, we have a GBC Ultima 65 laminator that is only getting hot enough to seal on the top roll. Bottom roller i... [Read more]
Mend ultima 65 laminator

ultima 65 laminator?

On our ultima 65, the laminate is not sealing well on the edges
Mend 65 up will not run

GBC Ultima 65 will heat up but will not run?

The only problem , until now, was that it would sometimes try to go in reverse when were pushing "run" and fee... [Read more]
Mend 65 will not heat up

Ultima 65 will not heat up?

Ultima 65 will not get hot enough.
Mend reset started work

GBC Ultima 65 keeps throwing reset button?

I have a GBC Ultima 65 laminator that started throwing the reset button ever so often. Pushed the reset button... [Read more]
Mend power lights turned

GBC HeatSeal Ultima 65 has no power?

The on/off switch at the back lights up when turned to on. However, there is no power to the rest of the mach... [Read more]
Mend laminator heat gbc

Ultima 65 laminator heat up but does not run when button is pushed?

Our GBC ultima 65 laminator turns on and heats up. When the heat indicator shows that it is ready, I push the... [Read more]
Mend ultima 65 laminator

Where can I get bearings for the ultima 65 laminator?

I see that the bearings for the ultima 65 can be purchased for less than Retail. Where can I get these beari... [Read more]
Pages 321

Ask Question

Ask your question Do you need free help? Ask your question.

howtomendit.com for free repair help, information and advice.
Ask Question