Recent: Lg vcr?

Mend > Document Laminators

Mend Bob Haller Ultima 65 Heat

Heat roller Ultima 65 Bob Haller you out there???

Bob I have another Ultima 65 that has a heat roller swollen in the middle. (apparently My name is getting around this school district). Any suggestions for getting the roller(s) at a reasonable price.
Thanks
Pat

Pat
October 2014
Bob HallerBob Haller Ultima 65Office Appliances, Document LaminatorsHeat Ultima 65
I currently have some used but in excellent condition heat rollers from ultimate 65s/ Feel free to call me if you need some....

The money will go to a good cause, we took in some friends of my fiance, they were 4 in a home with no heat, and no food. Theres a long story that goes with these special needs group. All proceeds will go to help them. We are waiting on government help which is very slow coming.

bob haller service and sales 412 848 0101
December 2014
Sorry I didnt see this earlier. In any case give me a call. You will need both the roller and heater set. The heaters sometimes gets a hot spot which makes the roller swell kinda in a area, sometimes the roller looks fine cold but looks bad, loose when hot. Might as well replace the roller bearings on the rollers while you have it all apart. Its a big job. Parts cost new from GBC about a grand:( There are options perhaps your district has a junk machine sitting around somewhere?

Bob Haller service and sales 412 848 0101
November 2014

Automatic Answer

We may have found other answers which could help you.

Click here for Heat Ultima 65

Related Questions ...

Mend gbc ultima hot
1

GBC Ultima 65 laminator?

My GBC Ultima 65 laminator keeps overheating because the bottom roller wasn't heating, so the top would get t... [Read more]
Mend wont heat up
2

how to fix GBC Ultima 65 roller that won't heat up?

The top roller of our GBC Ultima 65 heats up but not the bottom roller. What might be wrong and how do I fix i... [Read more]
Mend heat ready laminator
1

Heat light continues to flash on my GBC Ultima 65 even though it is ready?

The heat light continues to flash on my laminator even though it says it's ready. Why is that?
Mend hot s burning
1

GBC Ultima 65 Smells Hot, Like It's Burning?

I've Cleaned the Residue From the Ends of the Heat Rollers and Users Say It Still Smells. They have theorized... [Read more]
Mend gbc 65 heat
1

our GBC Ultima 65 control panel is not on?

Our GBC Ultima 65 control panel is not on. The laminate frolled into the heat rollers and the control panel ... [Read more]
Mend gbc ultima 65
1

GBC Ultima 65 Doesn't heat up?

We've replaced the coils and the circuit breaker. Finally checked for power. We have current going into the ... [Read more]
Mend gbc ultima 65 laminator
2

GBC Ultima 65 Laminator?

Laminator runs fine for about 2-3 feet of lamination, then just stops-power is on, heat is on, rollers just st... [Read more]
Mend 65 up will not run
1

GBC Ultima 65 will heat up but will not run?

The only problem , until now, was that it would sometimes try to go in reverse when were pushing "run" and fee... [Read more]
Mend 65 will not heat up
1

Ultima 65 will not heat up?

Ultima 65 will not get hot enough.
Mend power lights turned
2

GBC HeatSeal Ultima 65 has no power?

The on/off switch at the back lights up when turned to on. However, there is no power to the rest of the mach... [Read more]
Mend laminator heat gbc
1

Ultima 65 laminator heat up but does not run when button is pushed?

Our GBC ultima 65 laminator turns on and heats up. When the heat indicator shows that it is ready, I push the... [Read more]
Mend ultima 65 laminator
2

Where can I get bearings for the ultima 65 laminator?

I see that the bearings for the ultima 65 can be purchased for less than Retail. Where can I get these beari... [Read more]
Mend turned minutes suddenly
1

GBC Ultima 65 power issue?

We have GBC Ultima 65 laminator. Recently when it is turned on, it will heat up for about 5 minutes and then s... [Read more]
Mend gbc 65 heat
23

GBC Ultima 65 keeps stopping?

After turning on my GBC Ultima 65 and allowing it to heat, it runs about 6 inches of film and then stops. We h... [Read more]
Mend Office Appliances, Document Laminators

How do I stop the overheating of our Ultima 65 laminator?
Mend Office Appliances, Document Laminators

How Can I Fix a GBC 620 0S,2013?
Mend laminator ultima 65

Laminator gbc ultima 65 How to reinstall a power switch?
Mend Office Appliances, Document Laminators

How do I replace a fuse in the 4250?
Mend Office Appliances, Document Laminators

How to Remove an item from a Fellows Mars A4 laminator?
Mend buy machine not

the machine shows the red light on, buy that's all. the machine does not ?
Mend Office Appliances, Document Laminators

How can I repair my GBC Pinnacle 27?
Mend Office Appliances, Document Laminators

G5640 Laminator?
Mend turn machine indicator

GBC DocuSeal 95 Roller Won't Turn?
Mend work bought ideas

my new blusmart laminator dont work when plugged in?
Mend laminator motor rollers

How can I mend my Seal RL918 Lamination machine?
Mend gbc ultima hot

GBC Ultima 65 laminator?

How to mend ...

Find out how to mend just about anything howtomendit.com for free repair help, information and advice.
Mend Document Laminators ...

Related Categories

Mend Cash Registers
Cash Registers
Mend Document Shredders
Document Shredders
Mend Fax Machines
Fax Machines
Mend Photocopiers
Photocopiers

Topic

Ultima 65 Heat Roller Repair & Parts