5 hours ago: Will I need to replace my garden tap?

Mend > Document Laminators

Mend GBC Ultima 65 Laminator Heat Gbc

Ultima 65 laminator heat up but does not run when button is pushed?

Our GBC ultima 65 laminator turns on and heats up. When the heat indicator shows that it is ready, I push the run button but nothing happens. The rollers do not spin- nothing happens. What should I do? I appreciate the help. I am trying to save money for our preschool by doing it myself.

Emmie
January 2013
Hi I repair roll laminators for a living in the western PA area, as a indenpendent repair person. Around here GBC charges 317 dollars for the first hours labor, I have been told its 500 bucks for the first hour in california:(

In any case your machine refuses to run when you push forward? have you tried pushing reverse? can you hear the motor run when you push forward? A limited number of ultimate 65s have 2 circuit breakers facing downward in the bottom left rear corner close to being under the yellow reverse button. One breaker protects the entire machine, the other breaker when its there protects the motor circuit. You can carefully tip the machine backwards upside down to see the breaker or breakers. Had this machine occasionally ran backwards when you pushed run? If so the membrame switch is undoubetdly bad. If you were anywhere around pittsburgh I would give you a free on site no cost no obligation estimate. Feel free to call me phone help is ALWAYS FREE! like helping others.

bob haller service and sales pittsburgh pa 412 366 4906
January 2013

Automatic Answer

We may have found other answers which could help you.

Click here for Laminator Heat Gbc

Related Questions ...

Mend gbc ultima hot
1

GBC Ultima 65 laminator?

My GBC Ultima 65 laminator keeps overheating because the bottom roller wasn't heating, so the top would get t... [Read more]
Mend heat ready laminator
1

Heat light continues to flash on my GBC Ultima 65 even though it is ready?

The heat light continues to flash on my laminator even though it says it's ready. Why is that?
Mend gbc 4250 power
1

GBC 4250 No Power?

What happened: Co-worker went to use the rear cutting blade to cut off excess laminate while the machine was ... [Read more]
Mend gbc ultima 65 laminator
2

GBC Ultima 65 Laminator?

Laminator runs fine for about 2-3 feet of lamination, then just stops-power is on, heat is on, rollers just st... [Read more]
Mend 65 up will not run
1

GBC Ultima 65 will heat up but will not run?

The only problem , until now, was that it would sometimes try to go in reverse when were pushing "run" and fee... [Read more]
Mend laminator rollers heat
1

how do i clean my rollers on my gbc 4250 laminator?

I am trying to get my gbc laminator to work. The laminator takes a very long time to heat up.
Mend 4250 laminator heat
1

gbs 4250 laminator?

my laminator will not heat up. It worked yesterday...
Mend laminator thermal sensor
1

GBC 4250 with Heat at all?

Hi there, I have a GBC4250 Laminator that I purchased used and it has no heat at all, I did replace thermal se... [Read more]
Mend heating heat power
1

GBC4250 laminator not heating?

no heat on gbc 4250 power and ready light on is there a way to ck the heat sens board
Mend turn power switch
2

GBC laminator?

I have a GBC model 4250 laminator that when you turn on the power switch, it immediately says it is ready. It... [Read more]
Mend gbc 4250 laminator
1

how do you access lower idler bar on GBC 4250?

how do you access the lower idler bar to check the heat sensor on a GBC 4250 laminator
Mend gbc heat up
1

GBC 4250 laminator doesn't heat up?

I'm repairing a GBC 4250 laminator for a customer. When you turn the mach. on, the OK light comes on at the s... [Read more]
Mend gbc 4250 laminator
1

gbc 4250 laminator?

i can i tell if thermal cut-out or heat sensor is bad.
Mend pinnacle 27 help
3

My GBC Pinnacle 27 laminator does not heat?

My GBC Pinnacle 27 does not heat. It powers on but the heat shoes do not heat up at all. Any help??
Mend turned minutes suddenly
1

GBC Ultima 65 power issue?

We have GBC Ultima 65 laminator. Recently when it is turned on, it will heat up for about 5 minutes and then s... [Read more]

How to mend ...

Find out how to mend just about anything howtomendit.com for free repair help, information and advice.
Mend Document Laminators ...