accenta 6 alarm system?

My yuasa np2.8ah battery needs replacing.will the accenta 6 alarm system allow me to replace it with a yuasa np3.2np battery or should l replace it with a yuasa np 2.8 battery? The external dimensions of both batteries are the same.

Joe
September 2015

Hello i seem to have a small problem with a G4 accenta , iv just replaced a pir with the power off and battery leads off but now its powered back up i get the power led and day led on and when i enter the code or swipe all 8 zone LEDs show red ??? it didnt do this before and now i cant seem to set the alarm, has anyone got an idea please

Dan the Man
July 2014

Why we can't turn off the alarm?it just went on and on and on.tried to put off main switch several times but nothing happens. Pls help

josie
June 2014

Hi I have an accenta g4 mini system and have two bell boxes, front and back of the house. I have a six core from the panel to each of the boxes. As far as I can see the connections are all in correct terminals. But there is no sound or light signalling once in alarm mode. But just has a red led on all the time but. Instruction manual says there should be flashing lights.
Thanks for any help

jkeating
April 2014

I have a Accenta 8 mini alarm system.

I recently took the keypad panel off to wipe the key pad circuit board. i put the keypad panel back on which was great.

However a few days on i keep getting a Tamper led on and the alarm goes off. Even if the alarm is not set.

I can happen once a day or every other day or even twice a day. I have to put in my code and reset every time

Any ideas????

Carl
November 2013

For some reason now every time I go through a room it makes a beeping noise, it didnt before now its irrattating . Help please

gary whitehouse
September 2013

Hi the engineer code is not working and I cannot program the panel

Chan
July 2013

pir sensor is staying on......?

bud
September 2012

thanx

LEE
December 2011

where can i get the PCB inside a accenta 6 panel?

Roger
December 2011

Hi Sunny,
just moved into the house and i have an accenta 8 mini alarm system installed, which was working fine until recently.
it has now developed a tamper fault which activates when we switch on or off the D/Stairs toilet light/fan.
I cannot see where the fault is
Any ideas ??
ps I have just redecorated my hall where i had to take the pir/internal sounder alarm and control boxoff the wall but the wiring hs not been disturbed

thank You

tickityboo
June 2011

Hi I have an accenta G4 alarm and the keypad has had a problem. it will not allow me to enter my code. tried disconnecting power and reconnecting. it will not allow 9999 or 0123 engineer codes. just bleeps when you try and put in fourth number. when i walk past sensor it illuminates on panel and bleeps. cant set alarm. any ideas or do you think i need new keypad.?

accenta + keypad

flyboy
May 2011

Hi I recently changed my main door , which was wooden,there was a two metal thing .when they replace to PVC door I can't put fix that in that door.if anybody know any other way to fix or anything can do for it (accentra6). ?
Thank you.

Sudi
October 2010

thanks sunny!!!! you are brill

roger
August 2010

i can,t stop my alarm going off. i pull the main power in the box. to stop it i,v tried reconecting the power but it still going off. so i,v left it redundant

paul
June 2010

How can I turn the alarm off completly as I never use it

Orch
February 2010

just reset the system using the "Sunny method" Many thanks -

Ron I
December 2009

Sunny method by far the best. I did need to change 1 fuse on my Accenta 8 before the Sunny method worked but it worked like a dream and all systems now fully restored. Sincere thanks, probably paid half of my internet costs in saved call out charges

Charlie F
November 2009

Hi how do i swop my down stairs accentra key box to upstairs

tim
September 2009

Just moved to rented house. We noticed the blue light flashing on box, nobody knows the code. What can we do please we would like to use the alarm system if possible?
The programer on wall is accentra with reset chime etc.

Bob Fitzgerald
September 2009

Its simple!! Turn all your fuses off then back on again.. The alarm will go off for a few minutes it will then stop and yu will be able to reset the alarm... Simply type in your codes and it will reset!! It is honestly as simple as that!!

Nicole
August 2009

hi all..could you please help me with this question! i have a accenta 6 alarm ,for which just recently the bell box siren went faulty so i ordered a replacement like for like..i switched the power off to the alarm so that i can install the new siren ..the new siren on installing sounded whilst up the ladder for which i guess was due to internal battery connected,i refitted bell box cover no problem! and punch in my four number code to turn off alarm sounding outside and to reset the system.all was fine, but now for some reason on going out for the day i went to set the alarm and the keypad is not responsing to code,after several attempts i entered 1234 nothing happened?also tried 4321 still no response..the day light is on and power light is on,so im puzzled by this ..please could you help me with my question,i would be greatful .glenn w

glenn w
August 2009

Your panel processor has locked out.Remove mains supply and internal battery to reboot system. Suspect you need a new battery.

jb
April 2009

dear all i have had work done on house ie windows so had to take 1 pir sensor down i noticed that the alarm unit ie were you enter ur code didnt have power light on went to main panel have 230 volts coming into panel have 12 volts at battery terminals but no volts going out to control unit have checked fuses please does anyone have any info, idea,s many thanks

paul brown
March 2009

I had a similar problem to that of Cormac.
Power light on but nothing else.
I followed Graham's advice:-
"you may have to open the front cover on the main panel and look for the terminals marked PA there should be a pair of wires in these terminals, take them out and use a short piece of cable to put back in to these two terminals, once you have refitted the cover you should be able to press the reset button twice and regain control of the system"
and got the power to the keypads but the tamper light stayed on.
I then followed Sunny's advice:-
you need a full power down - ie.

Switch off mains
Open lid to main panel
Take away one battery lead
Switch mains back on
Put in code
Put back battery clip
Close lid
Press reset
The end"
My system is now up and running perfectly.
Thanks Graham and Sunny.

Peter K
March 2009

I followed Grahams instructions on this one and it sorted me out ie was able to regain control of the alarm. thanks Graham. What about the 2 wires removed from PA terminals though.. What was their function in life?, as they are now redundant with a link in to connect terminals 13 & 14.
thanks
cormac

Cormac Garvey
December 2008

you may have to open the front cover on the main panel and look for the terminals marked PA there should be a pair of wires in these terminals ,take them out and use a short piece of cable to put back in to these two terminals,once you have refitted the cover you should be able to press the reset button twice and regain control of the system

Graham c/o Total Security Lancashire
November 2008

we are moving to a house,but the previous owners do not know the alarm code,how do I change the code without knowing the previous code.

mick maher
September 2008

how to set a new number as the key pad is fading where it is used too much

barrie greene
July 2008

hi we had to disconnect our alarm for abit and the tamper switch wont go off we cant reset the alarm the red and green light is on i gather that is the power and tamper switch can anyone help pls

diane
June 2008

Hi Sunny

I wonder if you or anyone else could help. We have moved into a house that has an Accenta alarm system installed. There are 2 PIR's also, one in the lounge and one on the landing. We changed the code when we moved in and all was working fine. We decided to decorate the kitchen. On the kitchen wall is an unsightly small 3 inch wide by 5 inch high (approx), silver box. It has an opening at the top of the box and inside is a piece of wood. The front panel of the box has a keyhole and there is a key. By turning the key just moves the box up and down. There is a similar box on the landing as well we've noticed. There are no wires or anything going into these silver boxes and so, having no idea what these silver boxes are, and because they are unsightly, I decided to remove it when we were decorating. However, as I tried to do this it activated the alarm. I entered the code which turned the alarm off, but left the alarm keypad unresponsive. The, Attack, Day and Power lights were illuminated. I opened the alarm central control panel and took a wire off the battery, fiddled with the silver box again to see if I could work out what it does, this time the alarm didnt activate so I went back to the keypad and in addition to the Attack, Day and Power lights, the Tamper light is now on.

Then I read your solution above, I unclipped a battery lead, turned off the mains power, and this activated the alarm, we keyed in our code which de-activated the alarm, we clipped the battery lead back in, but once again the keypad is unresponsive and now the Day light has gone out but the Attack, Tamper and Power lights are on.

I've looked at the glass fuses and they all seem ok. Could you help advise us what we need to do to rerstore our alarm to a functioning one, and what are these blasted silver boxes for?

Thank you.

Andie
January 2008

fuse in juntion box has blown should be near control panel, if not there is a fuse inside tha control paner where the power leads merge

Tyrone
January 2008

you have probably blown one of the glass fuses inside the main control box !!!

peter
May 2007

you need a full power down - ie.

switch off mains
open lid to main panel
take away one battery lead
switch mains back on
put in code
put back battery clip
close lid
press reset
the end

sunny
August 2006