Recent: Fix food processor motor?

Mend GBC Document Laminators

Office Appliances, Document Laminators howtomendit.com find out how to mend just about anything.
Categories

Mend Gbc

Free repair help

We have 101 questions about mending 'gbc' in category Office Appliances, Document Laminators

How to mend ... Gbc

Pages 54321
Mend gbc 4250 laminator

How can I repair a GBC 4250 Laminator?

I'm a teacher who is pretty handy. I've already fixed a few problems with this laminator before but now I'm s... [Read more]
Mend Office Appliances, Document Laminators

Thank you to Bob Haller!?

Dear Bob, I want to thank you for the advice you post. I was able to replace the roller bearings on a twelve ... [Read more]
Mend 65 up will not run

GBC Ultima 65 will heat up but will not run?

The only problem , until now, was that it would sometimes try to go in reverse when were pushing "run" and fee... [Read more]
Mend Office Appliances, Document Laminators

My GBC Ulltima laminator just keeps getting hotter?

If it is a thermostat issue, can I purchase a thermostat and install it myself?
Mend reset started work

GBC Ultima 65 keeps throwing reset button?

I have a GBC Ultima 65 laminator that started throwing the reset button ever so often. Pushed the reset button... [Read more]
Mend gbc 4250 laminator switch

GBC 4250 Laminator - overheated (thermal switch / transistor)?

Our school has a GBC 4250 Laminator. It went dead while it was operating. From the posts I have seen this in... [Read more]
Mend power lights turned

GBC HeatSeal Ultima 65 has no power?

The on/off switch at the back lights up when turned to on. However, there is no power to the rest of the mach... [Read more]
Mend going cold easy

4250 GBC Laminator?

We are going to all cold lamination...is there an easy way to turn off the heaters on the 4250?
Mend clean long heat

how do i clean my rollers on my gbc 4250 laminator?

I am trying to get my gbc laminator to work. The laminator takes a very long time to heat up.
Mend circuit board fell

Schematic to reconnect circuit board on GBC 4250?

The side compartment of our GBC 4250 laminator fell off and the wires became disconnected from the circuit boa... [Read more]
Mend laminator heat gbc

Ultima 65 laminator heat up but does not run when button is pushed?

Our GBC ultima 65 laminator turns on and heats up. When the heat indicator shows that it is ready, I push the... [Read more]
Mend gbc ultima rollers

How do I remove the film rolls from the GBC Ultima 65?

I have trouble EVERY time taking the film rollers off and putting back on, especially on the bottom. Everyone ... [Read more]
Mend Office Appliances, Document Laminators

Why does my gbc laminator 1064 beep constantly when its running?

Why does my GBC Laminator 1064 beep constantly when feeding in material?
Mend gbc 4250 heat

GBC 4250 with Heat at all?

Hi there, I have a GBC4250 Laminator that I purchased used and it has no heat at all, I did replace thermal se... [Read more]
Mend Office Appliances, Document Laminators

GBC Ultima 65 - new rollers needed!!?

I am reading Bob Haller's info about these laminators. I work in a public school in East San Diego County (Pin... [Read more]
Mend Office Appliances, Document Laminators

gcb 4250 overheated, calling Bob Haller please?

I started searching for info on troubleshooting a GBC 4250 and came across a few posts on here so I'm hoping B... [Read more]
Mend gbc 4250 laminator not turn

GBC 4250 laminator does not turn on?

Have troubleshot. Had laminate roll around exit rolls; didn't know about reverse button (no manual); turned of... [Read more]
Mend power switch works

GBC 4250 Laminator won't heat?

The power is good. The lid cutoff switch works. The Thermal cutoff is on (not cutoff). The heat sensor reads 4... [Read more]
Mend fuse worked yesterday today

gbc 4250 blows fuse?

i have a gbc 4250 laminator it heats up fine it worked yesterday today when i went to use it and turn on the ... [Read more]
Mend gbc 4250 laminator

GBC 4250 Laminator....dead?

We have a GBC 4250 Laminator that seems to be completely dead....the fuse is good, so we are trying to figure ... [Read more]
Pages 54321

Ask Question

Ask your question Do you need free help? Ask your question.

howtomendit.com for free repair help, information and advice.
Ask Question