How to mend ... Sensor Going Control Panel

indesit dl620uk not heating?

Have an indesit dl620uk which is not heating. the water. Have checked the element and the impedence is as expe... [Read more]

9751 alarm with tamper fault?

Folks, I have inheritted an alarm system with the purchase of a new house. It's a Watson Alarm system but i... [Read more]

Maytag LSG 1000 (washer / dryer combo)?

Maytag LSG 1000 / washer / dryer combo: The washer's H2O level becomes too high when on the "large load" sett... [Read more]

zanussi washer error codes relating most models?

E11: Difficulty in filling during wash phase E13: Water leakage. E21: Difficulties in draining . E23: Malfunct... [Read more]

alarm will not set - veritas 8c?

Have tried everything in manual under trouble shooting. Alarm will not set have done all e.g the walk test, st... [Read more]

veritas 8 alarm problem?

My husband unscrewed a sensor in the bedroom on our veritas 8 alarm so he could decorate behind it,after it wa... [Read more]

how can i fix my house alarm veritas 8?

even when the alarm is not set each sensor you pass sounds a bleep at the control panel. why?

error code E2?

Crosley front load washer Model # CFW-8000GW/GR/GS/GBL. I HAVE ONLY HAD THIS MACHINE FOR 2 YRS, shouldn't be h... [Read more]

How easy is it to replace the battery for Gardtec 300 Series Alarm?

I have a Gardtec 300 Series alarm which I have had for about 9 years now. Recently it seems to go off regurlar... [Read more]

heater.ford ka, 1996?

we have got a ford Ka and we had fixed the 4 speed control that works but it still blows cold air, also replac... [Read more]

Help with Veritas R8, tamper light and zone 2(Hallway)?

Help with Veritas R8, tamper light and zone 2(Hallway)? Help with Veritas R8, tamper light and zone 2 Can no... [Read more]

Johnson Starley JB25-30 burner fires up but only runs for seconds?

Hi Any advice would be appreciated, we have a Johnson & Starley JB25-30 Modairflow series 2 system. The probl... [Read more]

the light is flashing to say fault on control panel sensor, is this going t?

I have a baxi combi boilers model 80e, my heating comes on for a while and then the neon light comes on saying... [Read more]

How to remove the tamper on the control panel on my scantronic 9450 unit?

I have a scantronic 9450.I have just replaced a door in my hallway and replaced the old door sensor into the n... [Read more]

e8?

Why do i get E8 come up on my Daewood washing machine, where can i get a new Control panel or sensor from.

boiler lights, but just ticks over, IE: it won't go to full flame?

The boiler is a Radiant RS24. It lights, but stays on tickover. We've had a new pcb, limit thermostat and heat... [Read more]

where is the 02 heater sensor on my 1.8 2001 picasso?

where is the 02 heater sensor on my 1.8 2001 picasso the heater wont work and the wires going to the control p... [Read more]

Faulty Scantronic 9800 main control panel?

I have a 1992 (year) Scantronic 9800 main panel & remote. It has been very reliable. Last week it lost mains... [Read more]

Veritas 8 alarm, cut through sensor (pir) wire - help?

Hi I was recently doing some DIY and removed a skirting board. Unbeknown to me inside it was the wire that l... [Read more]

how to fix it?

does each pir sensor need its own cable going to control panel