How to mend ... Should Fit Place

Problem with Scunci SS-1000 hand steamer?

I've got a Scunci SS-1000 hand held steamer. When steam stopped coming out I pulled the unit apart to clean th... [Read more]

clutch?

ive got a ford transit connect van 53 plate 120000 miles i replaced the full clutch and slave cylinder 16 mont... [Read more]

Petrol tank under pressure, blowing petrol lines out?

I recently replaced the petrol lines in my blower, and ever since, after about 30 mins of use, one of the petr... [Read more]

How do you replace sliders / gliders on tilt & slide patio doors?

I have some tilt & slide patio doors and the glider / sliders have snapped, they hold the door in place as it ... [Read more]

place back again the oven door cooker Bompani BO 240 ya?

it was not too difficult to take out the door of cooker Bompani Bo 240 ya snd replace the hinges but I cannot ... [Read more]

how to remove the central dash to fit a stereo patch lead ?

i have fitted my sony stereo in my renault megane II it's a '53 plate 1.4 16v, it works, but every time the ca... [Read more]

Neff U1452 - How to replace Controller Switch?

Hi The controller switch to the main oven has come out - the switch itself, spring and small brass 'wheel'.... [Read more]

Can you swap a 04 2.3 iveco engine for a euro 4 2.3 will it fit?

Can i put a 04 2.3 iveco engine in place of a euro 4 2.3, is this possible

Gas Alarm position?

I have been given a battery operated Gas Alarm. Where is the best place to fit it? Should it be near floor lev... [Read more]

kitchen mixer tap turns off but continues turning back on?

Hi If I turn our mixer hot tap off it will shut off the supply but then a fraction of a turn further and the ... [Read more]

is it easy to fit new door check stop chek on citroen picasso ?

do i have to take door panel off to install new door check stop or can this be put in place from the outside o... [Read more]

how do I fit carbon brushes in hitachi mini grinder?

I'm having a problem fitting the spring with it's"cap"in place and then screwing in the retaining cover.

How does the outlet hose fit into my Seimans WM14S494GB/23 Washing machine?

I have a Seimans WM14S494GB/23 Washing machine. The outlet hose developed a leak and I have brought a new outl... [Read more]

table saw?

i have a table saw pp250ts witch has broke the casting witch holds the blade in place and had broken away and ... [Read more]

How do I fit a new lid to Bosch formula 1800W vacuum cleaner?

We broke the hinge pins off the lid of our Bosch formula 1800W vacuum cleaner so I ordered a new lid from Bosc... [Read more]

how to remove the pullstart pbc3020 strimmer?

still need help cannot get the pullstart cover off the machine the silver driveshaft piece infront of ... [Read more]

Can't fit bag into ProAction 1400 VC2940RD?

Hi, We have been given a second hand Pro Action 1400 vacuum cleaner (VC2940RD). When we got it, we tried it o... [Read more]

how do i change ignition switch on a vauxhall corsa?

the ignition switch has sheared the spindle at the end of the lock barrel and i need to get the old unit off t... [Read more]

Electrolux Caravan Fridge, Model 4271?

The jet does not fit very secure on top of the gas inlet, is there any kind of clip that holds this in place? ... [Read more]

can a intergrated washing machine be used?

can a intergrated washing machine be used in place of a freestanding one? I have limited height under the wor... [Read more]