How to mend ... Down Chain Bar

Poulan 17" 3.6 cu in & Partner P85 chainsaws from the 1970's?

No matter what I do, the saw will not quite start up. it goes for about a half a second at best then dies. I c... [Read more]

how to tell if i need a new chian and or a bar for my 16 in. gas mcculloch?

how do i determine if i need a chain and bar for my 16 in. gas Mcculloch chain saw? it is a model 1635 Mccull... [Read more]

How can I fix my Craftsman no tool tensioner?

I will see my chain is loose, stop cutting and adjust as usual then after a few minutes I see the chain is loo... [Read more]

why is my chain not getting oil on it why i cut?

when cutting with my saw, no bar oil is making it to the chain. It heats up then suts off. when the saw is s... [Read more]

my saw cuts on a curve?

my saw will not cut straight....rather it curves towards the left. i've sharpened both sides as evenly as i c... [Read more]

Where can I purchase a replacement bar and chain for Eager Beaver?

I need a replacement bar and chain for a Mcculloch Eager Beaver 2.3 ci, Model number 60014503. Can anyone tell... [Read more]

HOW CAN I FIX MY CHAINSAW?

I just got a brand new craftsman chainsaw.i was cutting the other day and the chain came off.i put the chain b... [Read more]

Need to know the proper chain size for a Homelite/Textron XL chainsaw?

I have an older small XL Homelite chainsaw. The chain bar measures 12 1/2 inches, and the old chain measures 1... [Read more]

Chain not oiling on Stihl 024?

How di I incerease the chain oiling on the bar on my Stihl 024, It has been getting less and less for some tim... [Read more]

How to replace chainsaw bar studs?

I have a Craftsman 3.7 chainsaw. The studs that hold the guide bar in place when you tension the chain loop a... [Read more]

Chain oil leakage CRAFTSMAN C944.411371 16in Bar?

I have a Craftsman 16 bar chainsaw. It has seen very little use. Cannot keep chain oil in it. It seems to lea... [Read more]

how can I fix my homelite d3850b chainsaw?

I have been using my saw up to today without any problems.My bar oil is not lubricating my chain and bar anymo... [Read more]

McCulloch "Timber Bear" 600 series how to properly re-set chain brake?

I was trying to properly place my bar on the chain tightening screw, and wasn't paying attention to the locati... [Read more]

Chain does not move?

Motor runs fine, everything is clean, but chain does not move. It froze up during operation and I cannot get i... [Read more]

chain does not get oiled, oil ends up in combustion chamber during storage?

I have a homelite XL 12 in. (old) the chain does not get proper oil and I'am sure the chain oil is ending up i... [Read more]

how do i tighten down chain bar?

when replacing the chain on my wild thing chains saw there are 2 bolts and a tension screw when i tighten the ... [Read more]

How do I get the oil coming out of my chainsaw onto the chain, not casing?

How do I get the massive amount of oil that is coming out of the automatic bar and chain oiler (Craftsman 18" ... [Read more]

Hot water tap for the bath not working properly?

Hi Guys, Hoping someone can give me some sensible advice. I've got a combi boiler(Valliant TurboMax), and i... [Read more]

How do I fix my cahinsaw oiler?

How do I fix my cahinsaw oiler? It is a craftsman chainsaw model # 358.351062. It has a 16" bar, 2.2 cu. in. (... [Read more]

removing CV driveshaft?

1990 Ford Tempo Automatic driver side CV shaft. I have the shaft fully loose except for the in joint connecte... [Read more]