Miele Novotronic Premier W800 spring/shock absorbers?

Excellent guidance in both posts above. Shock absorbers replaced in W800 using the above notes. I inspected initially using 1st posted method and later did the replacements by tipping machine on side to give access from under the machine. A combination of sockets and open spanners used. Replacement parts bought from online auction site supplier at £37. Bargain ! Thanks to those above for taking the time to write a first class idiots guide for this repair.

Frank
February 2013

A couple of things: I was looking for a baby guide to shock absorber replacements.... everywhere it is said that it is "easy".. but none of the descriptions of the work that I read were complete. So, this is my attempt.

First, our W820 has no bottom plate, so access is possible through the base, contrary to what has been written: BUT, you might not need it.. read below.

The steps are as follows:
1) Open the washer door. Turn off and disconnect the power.

2) Remove the top: To do this, take out the two plastic screw covers on the left and right of the top and undo the screw. (Crosshead). The top can be hinged backwards and then lifted off.

3) Inspect the drum. Push it up and down; if it bounces more to one side then that is probably the location of the faulty shock absorber. It is good practice to replace both shocks at the same time. However in our case a repair man fixed just one ! a year ago and the bouncing showed that the shock on the right was faulty.

3) Remove the washer front panel. You do this as follows:
a) Remove the soap drawer and put it to one side, pulling it forwards and depressing the red plastic lever visible towards the rear of the drawer. This allows it to be slid out.
b) Remove the three star-headed screws holding the soap drawer surround in place (I used Allen screw drivers for this.. not good I know).
c) Open the panel used for draining the machine (front panel, bottom left) and unhook the plastic drain pipe which clips into the door.
d) Remove three 10 mm bolts from the front panel. These are around where the wash door would normally close (I hope you left it open from step 1)
e) The front panel can now be hinged open (hinges on the right) and you should be able to see inside. Take the opportunity to clean up any visible mess.

4) Inspect the shock absorbers. The right hand shock is visible through the bottom right of the front of the machine. It is a metal cylinder about 6" long fixed at an angle. The left shock is visible but hard to access from the front.

5) In our case we only need to replace the shock on the right. You need a 13 mm ring spanner and you can do the removal entirely from the front... without even moving the machine. Undo the bolts at the top and bottom of the shock and pull it out. Inspect it for confirmation of fault. In our case there was NO resistance to movement at all. If it looks to be in good condition then it is probably the other shock causing the problem. In any case replace both.

6) The left-hand shock needs the machine put on its side for access through the base. Put down some cushioning material, blankets, heavy cardboard, etc to protect the sides and gently tip the machine. Ideally this is a two-person activity. If not, be careful! Again, with a 13 mm ring spanner unbolt and replace the faulty shock.

7) How tight should you bolt the shocks.. as tight as you can with one hand. The machine is robust.. but breakages can occur if the ring spanner slips and hits wiring or connectors, so ensure that the spanner is always fully home on the bolt head and wiring pushed out of the way. I protected my hand from spanner slippage by wearing a gardening glove for this part of the operation.

7) Now all we need is to reassemble:
a) First close the front panel and bolt it shut with the three bolts around the door. These take the strain and should be bolted first.
b) Then we put back the three screws holding the surround for the detergent drawer. Don't over tighten.. it just needs to be firm, not rigid.
c) Reattach the drain plug to the door of the access panel (bottom left) and close it.
d) Lastly, replace the top of the machine, attaching the rear of the top first and hinging downwards, and then use the two screws and plastic screw head covers to complete the job.

You should now have a working Miele with several more years left to run.
When we bought our first Miele (in Holland) it had an expected lifetime of 20 years according to the store. It survived for 20 years, surviving moves across 3 countries. We then tried Hotpoint.. total rubbish and it died after 3 years. We are now on our second Miele and it is around 17 years old and, with this repair, working perfectly. Perhaps one more will see us into (and out of) retirement. In the meantime, it is worthwhile keeping these excellent machines in good condition. They are not throw-away!

George Brooke
January 2013

Yes, the shock absorbers are the most likely cause of the problem. Replacements are available from various sources on the internet - eg Buyspares.co.uk - and cost about £65 for a pair (you need 1 pair).

The shock absorbers are simple to replace - basically just one bolt at each end of each shock absorber. However it is necessary to have access to the base of the machine. There is no base panel - the base is just an open space. Just turn the whole machine on to its side (carefully because it is VERY heavy - two strong people needed) and then, on your hands and knees, you can see the shock absorbers and reach inside the machine to replace them.

Obviously you must switch off the power and disconnect the plug from the mains supply before beginning work.

The drum springs can be replaced from the top of the machine which slides off after removing two screws - one either side near the front of the top rim. The drum hangs on four springs - they cost about £6 each - so replacing them one at a time should be OK (I have never done this but it looks relatively simple). One of the springs is hidden beneath the soap tray assembly so it will be necessary to remove the whole tray assembly before proceeding. Instructions for removing the soap tray can be found in other answers.

I would replace the shock absorbers first because they are the most likely cause of the problem in my opinion. However it would not be too difficult or expensive to do the springs as well.

Hope this helps. I realize my answer is not very detailed but the job is fairly self-explanatory once you see the open base of the machine.

Rod
May 2010