Recent: Safely remove screen protector from a Macbook Air?

Mend > Home Alarm Systems

Mend Scantronic 9448+ Set Replaced

how can i set my alarm and give it a new code scantronic 9448+?

ive cut some wires which set my alarm off. i connected the wires again and replaced a fuse but i cannot set my alarm anymore. is there a factory setting code .nothing happens with my code

john mcdermott
February 2008
ScantronicScantronic 9448+Security Systems, Home Alarm SystemsSet Scantronic Replaced
after how do you reset the alarm anddo walk test

jesse
April 2012
i dont a manual

jesse
April 2012
i am asking you now if i knew the answer i wouldnt ask you this question

jesse
April 2012
factory defaults ? start new instalation guide page 28,restoring factory defaults .then start from scratch good luck.

graham [in greece]
February 2008
key in 6 then arrow[bottom right on key pad] then existing user code ,then same code again,[you should hear 2 beeps],then new4 digit code [and should hear another 2beeps] your user code has now been changed.

graham68808
February 2008

Related Questions ...

Mend security alarm tamper
3

Tamper won't go off?

My Scantronic 9448 had 12v at the pcb but the pcb and lights did not light up, so I replaced it with my spare,... [Read more]
Mend stopped entered set
2

My Scantonic 9247/9889 simply stopped arming when code was entered?

We can't set our Scantronic alarm. We found the battery dead and one of the three internal fuses blown. We rep... [Read more]
Mend alarm home security battery
4

scantronic 9449/9427 alarm activating when setting alarm?

Recently replaced the backup battery and now when I set the alarm the alarm activates and when I enter the cod... [Read more]
Mend box alarm panel
12

How can i wire my bell box?

Hi I replaced my scantronic 9450 alarm panel with scantronic 9651.I have got the pirs and door co... [Read more]
Mend security system programming
29

9425 scantronic keypad?

I have replaced my keypad with a used one, which I have been assured it is in perfect working order after my o... [Read more]
Mend security system programming
2

No entry time?

I have replaced my old accenta for a scantronic but the alarm activates as soon as my entry exit door is opene... [Read more]
Mend scantronic alarm help engineer
9

Scantronic alarm?

Hello all hope you can help?. Had an engineer out a fortnight ago now who replaced a sensor and the batteri... [Read more]
Mend security system battery
8

scantronic 500?

hi my alarm went off recently even though it wasn't set,I entered my code and the alarm stopped,but the tamper... [Read more]
Mend alarm security system control panel
8

Control Panel flashing Rf problem?

My eight year old Scantronic 500r+ free wire alarm with four 515r PIRs have never given any problems until rec... [Read more]
Mend replacing hello replaced
1

replacing battry?

hello all I have just replaced the battry in my scantronic 9800. after pressing 99 on my upstairs key pad it... [Read more]
Mend remove control panel
1

How to remove the tamper on the control panel on my scantronic 9450 unit?

I have a scantronic 9450.I have just replaced a door in my hallway and replaced the old door sensor into the n... [Read more]
Mend set replaced battery
1

Scantronic 9448?

The external alarm went off in the middle of the night, although the alarm was not set. I replaced the batter... [Read more]
Mend security battery fault
3

had power failure now alarm not working?

neighbour cut electric power to my house while working on his drive. i had no electric for 5 hours. my alarm w... [Read more]
Mend reset alarm system
2

Scantronic 9200 still will not reset?

Thanks to Neil from Tritec alarms for replying, the Scantronic alarm system will not reset,this is following a... [Read more]
Mend security system fault
1

Scantronic 9450 - Can I obtain a replacement Outside Box?

Scantronic 9450 Alarm Intermittent fault. The alarm occasionally sounds when not set. I am almost certain ... [Read more]
Mend alarm security system home security

Scantronic 9651 alarm?
Mend system reset scantronic power

SR system reset on Scantronic 9827 after total power failure?
Mend phone number company

How can I upgrade my Scantronic 9827 home alarm?
Mend alarm scantronic reading

Alarm?
Mend alarm security system battery

Scantronic 9427 Alarm?
Mend smoke security system

Reset system after smoke alarm sounds & user manual request?
Mend security alarm tamper

Tamper won't go off?
Mend house alarm scantronic keypad

How can I send house alarm?
Mend alarm security system

How can I reset a Scantronic 9427?
Mend alarm panel home alarm scantronic

House alarm Scantronic 9427?
Mend scantronic alarm battery

How can I stop beeping?
Mend security system scantronic

Disable Alarm Scantronic 9800?

How to mend ...

Find out how to mend just about anything howtomendit.com for free repair help, information and advice.
Mend Home Alarm Systems ...

Other models...

Scantronic 4600Scantronic 500r+Scantronic 816Scantronic 9000Scantronic 9100Scantronic 9200Scantronic 9425Scantronic 9427Scantronic 9448ESScantronic 9449Scantronic 9450Scantronic 9452Scantronic 9454Scantronic 9651Scantronic 9751Scantronic 9800Scantronic 9800+Scantronic 9827Scantronic 9930Scantronic I-on 16

Related Categories

Mend Car Alarm Systems
Car Alarm Systems

Topic

Scantronic 9448+ Alarm: Reset & Code Help