Mend > Home Alarm Systems

How can i wire my bell box?

Hi
I replaced my scantronic 9450 alarm panel with scantronic 9651.I have got the pirs and door contacts all woking ok.I cannot get the bellbox to work.It is about 25 years old but still looks good and was working properly before i disconnected it.It was installed by an alarm company CSS and the bell has the company logo (CSS) on it so i do not know what make it is.
The way i wired the bell from panel is
Red from 12v aux to + off on bell
Black from OV to - hold on bell
Blue from TR to tamper on bell
Yellow from OP1 to bell on bell
Orange from OP2 to strobe on bell
In the bell there is a resistor between Red + off and Yellow bell.
The two small lights are flashing on the bell as if it is working normally,but it keeps bleeping quietly every few minutes and does not activate with the alarm.
There is also an other connection on the bell marked set but is not wired to anything.
I also notice that the tamper switch has never been wired to any thing by the company originally.
I know this sounds complicated so i hope someone
out there can help.Any help would be greatly
appreciated.
Thanks in advance

Shauki
March 2016

Scantronic Scantronic 9651 Security Systems, Home Alarm Systems Box Alarm Panel

Hi gts
Just to let u know,got the alarm working like a dream,replaced the pirs as well so hopefully it should last me a few years.
Thanks for all your help.now for that creaking floorboard on top of the stairs wheres my hammer??????

shauki
April 2016

no bend the lever on the micro switch to make sure when you put the blue cover on the blue button is pressed down by the bell box cover

gts
March 2016

Now I get it. You are talking about the new box when you are talking about moving and bending switch and white cover.
Confusion over.

Shauki
March 2016

ah the panel must be prog for resis in the units,no prob buy new bell box mate only a fool buys a battery for a unit that old he colours dont matter,we all use our own ,long as they go where they must:-)thank you for your reply ,if you fit our bell box you should be ok

gts
March 2016

Thank you for that gts.I have now got the bell to work and I do need the resistor in otherwise the bell rings continuously when connected up.Although when I took the bell down and wired on the bench next to the panel,it worked without the resistor. I wired it
yellow bell to op1
Orange strobe to op 2
Blue tpr to tamper
Red hold + to auxiliary +

The switch has never been wired to anything,so maybe moving it about might not make any difference.
It still clicking every few minutes but I think that is because the battery in the box needs changing,so I might end up buying another bell,as the battery costs ten to twelve pounds
including delivery and some bells are around twenty five pounds. your thoughts would be appreciated.

Shauki
March 2016

dump the resistor not needed

gts
March 2016

there is a clear cover under the blue one,i forgot about that

gts
March 2016

one more thing on the bell box the anti tamper micro switch has a lever ,you will need to carefully bend it push it a bit back and bend the lever so it takes up any space what i mean is push it up and back to bend it

gts
March 2016

we use the cqr multi box,now remove power from the panel mains and battery,remove all wires from the bell box on panel put white wire to the strobe connection on the panel,the blue wire to the bell input on the panel the red wire to the pos output on the panel the black wire to the neg output on the panel and finaly the yellow wire on the tamper return on the panel,then do the same in the multi box then all will be fine ,on the multi box fit the little wire from the battery onto the socket in bell box,then fit the blue cover then fit the outer cover,remove the little cap thats stuck to the inside of the cover,this is used to cover the screw that holds cover in place,then reconnect the battery inside panel,close panel lid then turn on mains power ,bobs your uncle,you should see a green and red led flash from side to side ,hope this helps

gts
March 2016

OK thanks for your advice. Which bell box would you suggest for this alarm panel

Shauki
March 2016

css connolly security systems good company in glasgow i know paul

gts
March 2016

buy a new bell box mate

gts
March 2016

Mend > Home Alarm Systems

How can i wire my bell box?

How can i wire my bell box?

I can answer this question ...

How can i wire my bell box?

Related Questions ...

Cooper Scantronic 9448 alarm?

CEF AP28 alarm issue?

On Logic 4 alarm circuit box cut to reset?

How can I stop outside panel flashing blue light ?

How can I fix my optima 2 alarm?

Nexus 8 alarm system - constant bell tamper fault?

texecom tamper light on when intheory should be off?

Veritable 8C no power?

Accenta 6 system?

Accenta Alarm Strobe flashing?

scantronic 9800 alarm a reply will be given thanks?

Flashing power light?

I have a flashing green light on my veritas r8 control panel?

alarm replacements ?

panel?

How to mend ...

Other models...

Related Categories

Topic