How to mend ... Replaced Belt Going

How do i fix my Bissell carpet pro, the self propelled seems to have stoped?

How do i fix my Bissell carpet pro, the self propelled seems to have stoped working. Is there a belt that need... [Read more]

Nordictrack Treadmill C2150?

Had 4 year and had 2 motors burn out, just replaced motor new one stops when I am running. I have lubes walki... [Read more]

How to find timing marks on Citroen Relay?

I have replaced timing belt on my Citroen Relay 2.2 TDi HDi van,and I need to know how to find top dead centre... [Read more]

i replaced the belt on my dirt devil vision,it melted the rollerbrush?

and the belt was melted,these are the same pack of belts i had used in the past.help

my beko dryer is blowing fuses?

how can i stop my beko dryer from blowing the fuses? my seal, bearings and belt have been replaced already

my2003 renault trafic 1900 cdi wont start?

driving my van 35 mph axillery belt snaped, van made a rattel noise at top of engine, drove in limp mode 1/2 m... [Read more]

how can i make the belt stay on my kirby classic 3 -2cb?

I replaced the brush roller and belt. when I placed the belt on the belt lifter and try to turn it, the lifte... [Read more]

What causes my washer to lock-up on the spin cycle with motor still on?

What causes the pulleys to lock-up when it comes to the spin cycle? I've replaced the belt and the switch tha... [Read more]

Hotpoint Aquarius vdt20?

I recently replaced the belt and since then the drum seems to be rubbing on the back panel and making a scrapp... [Read more]

2007 Scenic steering wheel?

I have just bought a 2007 scenic when we said we would have it I made a few demands, new cam belt etc. One pro... [Read more]

Our Whirlpool 3RAWZ480E is not working?

Without warning our machine has just stopped working. We have checked and cleaned all vents, replaced the fuse... [Read more]

Code E4?

My treadmill cuts off and shows an E4 code. I have changed the drive belt, replaced the motor, recalibrated, w... [Read more]

PCB Circuit Board?

When changing my drive belt (Hoover HDV6UK) I disconnect the wires from the PCB and did not take a picture. A... [Read more]

AEG oko lavamatic 610 electronic?

Hope you can help.. My machine goes through all cycles fine but the drum won't turn. The drive belt is tight e... [Read more]

Bosch wtl6003 motor fails to start after replacing broken belt?

I have a Bosch wtl 6003 Tumble dryer. FD 8308 000781. The belt broke which I replaced (from the rear of the ma... [Read more]

Is there a stat on a Beko DRCS76W dryer heater unit?

I have a Beko DRCS76W dryer which is only just blowing warm. Checking the resistance across each element shows... [Read more]

Maytag washer won't spin, LAT8426AAE?

maytag washer "Dependable Care" 14 yrs old. will not spin. I have read many, many articles on the net, "troubl... [Read more]

My drive belt snapped which i replaced Citroen Picaso 1.8 2001?

At first my battery would not hold a charge but now its gone and cooked my battery as it was red hot to touch ... [Read more]

how can I fix my Toledo belt sander TBS 800?

The drive drum on this sander has lost its rubber surface and will therefore not turn the sanding belt. Can th... [Read more]

asko 7005 dryer belt/motor ?

replaced the belt in my asko 7005 dryer withe the appropriate belt, and there seems to be a bit of slack in th... [Read more]