How to mend ... Motor Going Control

kenwood mixer A 901?

does anyone know what the component values are on the motor control backbord.there appear to be two resistors ... [Read more]

Blowing resistor (56ohm) on Kenwood Chef control board?

I have an old A901 Kenwood Chef. It has not been used for several years. I switched it on and it worked for ab... [Read more]

Hoover SIX 1200 drum won't turn - NOT belt?

Just removed top and rear covers and watched what happened on a spin cycle. Control box makes a lot of clickin... [Read more]

Lockout - Thermecon oil boiler, with a Minor 1 burner?

The boiler is 9 yrs old, regularly serviced. Just started to lockout on first sartup, morning and evening. Wh... [Read more]

Riello 40 not firing?

Hi, I ran out of oil during the night and turned off the control panel in the morning. I got oil delivered... [Read more]

bernina 530-2sewing machine motor?

Why is the suppressor on the motor of the Bernina 530-2 Record not needed? My machine will not start when I p... [Read more]

Carburettor settings for Fymo Venturer with Tecumseh HiTec40ES motor ?

I have a Flymo Venturer Mower with a Tecumseh Electric start motor.It has worked very well for many years with... [Read more]

Hotpoint Aquarius WMA34P?

Would not spin. Replaced brushes on motor, cleaned out bottom filter. Ran empty wash but when programme cycle ... [Read more]

What is wrong with my central locking on my Vauxhall Vectra 2.5 V6?

I have a problem with the central locking system. First, the front passenger door stopped unlocking about 2-3... [Read more]

heater fan?

The heater fan only works on full, I have replaced the control switch in the cab but it has made no difference... [Read more]

Kenwood chef A701A capacitor and other components?

I thiught it would be a good idea to replace the capacitor on my Kenwood Chef A701A because of its age and bef... [Read more]

Simpson MaxiDry 457 - Are you having reassembly problems?

Simpson MaxiDry 457 - The complete guide to disassembly & reassembly. After having spent nearly a whole wor... [Read more]

Has anyone got a solution?

I am having same problem all lights on control seem to operate but no air blowing through, fuses all OK, tried... [Read more]

Why is there Dishwasher Soap left in and on door after washer is done?

About half the time when the dishwasher is done washing there is still soap gel in and on the door. The repai... [Read more]

DIPLOMAT ADP 8352 All lights on plus beeping dry tray ,salt light on?

Power on, motor starts to run then beeps after approximately 5-10 seconds and all lights on control panel. The... [Read more]

Stopped running, but it lights up?

Have a Proform 985 treadmill. It will not run. Was working until recently. The power turns on, and the console... [Read more]

Can I get the fault codes for F & P washer GWL10U2?

In the process of replacing the drain motor and control panel, i lost the diagnostic codes. We reset the cont... [Read more]

LG WM1422SFD WASHING MACHINE?

FAULT CODE IN BOOK SAID MOTOR OVER LOAD.FITTED NEW MOTOR. FAULT CODE CAME UP AGAIN, CAN ANYONE HELP,IS IT A N... [Read more]

BOSCH exxcel 1000 motor wont run, changed brushes and control panel?

can't get the motor to run changed the brushes and the control panel. Anybody know of any other interlocks tha... [Read more]

How can I fix our Miele F1313S freezer?

The indicator lights all work but the motor does not run, even when the temperature control dial is turned up ... [Read more]