Recent: Safely remove screen protector from a Macbook Air?

Mend > General D.I.Y

Mend Scantronic 9448+ Alarm Zones

I have a scantronic 9448+ extra zones ?? ?

I have a scantronic 9448+ and have installed extra zones , but these are not coming up on walk test,
not sure either if I am in program/engineer mode ?
also is it possible to put a chime on the entry exit zone ??

Gaz1889
November 2011

Related Questions ...

Mend alarm security system home security
1

Scantronic 9651 aux dc fail?

I have just amended the programmed zones so that the kitchen sensor is not set when setting the system using B... [Read more]
Mend alarm security system fault
1

Scantronic 9000 series fault?

My house alarm has gone off and n0. 8 has appeared on the panel. This does not relate to any zones. Installed ... [Read more]
Mend sensor system tamper
11

How to reset a zone on Scantronic 9427 alarm system?

When I got in one of the zones indicated it had been tampered the sensor light above my patio door is flashing... [Read more]
Mend playing stopped working
3

Scantronic 9425 zone settings question?

Hi. My old 9425 Scantronic keypad is playing up: the 1 button has stopped working, so I can't set the alarm, a... [Read more]
Mend alarm security systems home alarm
12

how do i set up zones a and b. and b on it own on a scantronic 9651 alarm?

I got a alarm scantrinic one. 9651. had few problems with it. I don't know how to set up zones a and b. and b ... [Read more]
Mend alarm system reset fault
2

Scantronic 9800 - c1 alternating t1 (Temper Fault)?

I am a homeowner. I need help to reset c1 T1 fault on my alarm system. I have a SCANTRONIC 9800 ALARM SYSTE... [Read more]
Mend security sensors system
7

scantronic 9427 keeps going off?

Hi, my issue with this alarm is that when i set it to go to bed, with zones active downstairs with garage and ... [Read more]
Mend scantronic 9800 exit
4

scantronic 9800 entry/exit programming?

hi. i have a scantronic 9800 ,its been re programmed and have the following problem. entry and exit times are... [Read more]
Mend scantronic alarm wired
14

Scantronic alarm ?

Our alarm is part wired and part wireless,it seems it has forgotten our code that we have been using for years... [Read more]
Mend ion 16 unit
13

faulty scantronic ion 16 wireless unit?

my alarm is stating " jamming present " - tick to continue and then supervision fail - zones 03, 05 & 06 [ con... [Read more]
Mend help keypad batteries
5

can you help me please about aScantronic 9448ES alarm????‏?

i have istalled a 9448es with one keypad 9427... i did some mistakes in wiring and the two batteries whas belo... [Read more]
Mend reset alarm scantronic
3

How to reset my alarm? Scantronic 9452?

There was a powercut last week it set the alarm off. After 45 mins I entered of the usual code being entered u... [Read more]
Mend security home system
3

alarm will not let me program?

scantronic 9448 panel brand new replacing old 9448. all wiring the same,one set door contacts,2 pir,s.all un... [Read more]
Mend security system battery
4

Scantronic 9449 panel (with four 9427 keypads) fault problem... ?

9449 and keypads installed 13 years ago (by me). Faultless operation until now (only two minor 'prematures' in... [Read more]
Mend security zones system
4

Scantronic 9651?

The alarm panel does not use zones 6, 7, & 8 they are linked with wire loops, the alarm sounds sometimes for ... [Read more]

How to mend ...

Find out how to mend just about anything howtomendit.com for free repair help, information and advice.
Mend General D.I.Y ...