Recent: Home max fs506x?

Mend > Washing Machines

Mend Fisher Paykel GWL10 Fuse Main Board

How to diagnose Fisher Paykel GWL10 blowing its fuse?

I was able to take the main controller board out, and found that the 3A fuse was popped. So I soldered across the fuse on the board, and installed an external in-line fuse on the outside of the controller (to keep things safe!!! and accessible). Needless to say, the slow-blow 3A fuse keeps blowing (but now easily replaced). Can this be repaired at all? And where do I look?

Dean Fitzgerald
February 2009
Hi! I too am doing some repairs on my Fisher & Paykel machine and the fuse has blown in the process. Just a WARNING: If the fuse keeps blowing there is something wrong with the electrics/electronics. This is very DANGEROUS! Something is shorting somewhere and could give you a shock, possibly fatal. Without the fuse it would be other wiring in the machine that would blow, most likely in the "computer". You wouldn't be able to fix that and it would cost $100's to replace! Good luck, RJ.

RJ
February 2009

Automatic Answer

We may have found other answers which could help you.

Click here for Fuse Main Board

Related Questions ...

Mend washing machine fault repair hotpoint
1

Hotpoint WD865A stopped mid wash. 8pin chip U2 blown its to?

Hotpoint WD865A Washer Dryer.Just stopped mid wash. Plug,fuse ,mains filter OK. On Main Board IC U2, an eigh... [Read more]
Mend fuse motor drain
1

F&P MW512 Fuse Location?

Hi - we had a perfectly functioning machine until I decided to wash a quilt, figuring I would stand guard for ... [Read more]
Mend machine replace sensor
1

how can i fix my fisher paykel IW712 washing machine?

I had to replace the rotor sensor and did this no problems. The machine done 5 full loads with no problems and... [Read more]
Mend washing machine no power main board
16

Simpson Encore 605 - no power?

Hi, There is no power, nor any lights when turning machin on. Using a multimeter, I have tested: 1) ... [Read more]
Mend machine stops filling
1

W100Fw creda simplicity 1000?

machine stops filling and trips the main fuse board, also i have changed the inlet valve, but still nothing, h... [Read more]
Mend tripping fuse washing
1

zanussi wx1605 tripping rcd on fuse board?

hi My washing machine is tripping main rcd on fuse board thought about the heating element but machine is on 4... [Read more]
Mend washing machine programme filter
2

boschclassixx1000 Water goes in but nothing else?

Hi, My wife had a wash in a few days ago when the main trip went in the fuse board.She reset the trip and ... [Read more]
Mend hotpoint wm washer
1

my hotpoint wm 79 blows my main fuse box?

when i switch on my washer it trips the tripswitch on my main fuse board. have checked plug, and connection i... [Read more]
Mend washing machine heating element main board
1

Miele Premier 500 (W504) not heating water?

Hi, I purchased a Miele Premier 500 washine machine (used) about 3 months ago from a repair man who replaced ... [Read more]
Mend washing machine repair zanussi
1

ZANUSSI AQUACYCLE 1500 (FS1555W) WON'T START?

Working perfectly ok then founds main fuse blow on board blow, reset washing machine door shuts but the machin... [Read more]
Mend problem dryer bit
1

Hotpoint WD61 motor fails to run?

Problem with Hotpoint WD61 washer dryer: this may be a bit old now but it’s quite “low mileage” and does... [Read more]

How to mend ...

Find out how to mend just about anything howtomendit.com for free repair help, information and advice.
Mend Washing Machines ...