Kelvinator KD14SS dishwasher fault code?

I have an E3 error, how do i fix it please

margi
October 2016

Kelvinator KD14SS power is on front display is showing but I cannot program it the top display is dead. Machine does not want to operate.

Gareth
July 2016

I'd like to add to this thread as follows: I tilted the dishwasher to drain the water onto a towel and it worked - for a while. Then it started with the blinking lights again halfway through the wash cycle and it started to leak badly. I discovered that there is a pipe which feeds to the top of the machine to spray the dishes from above, which had disconnected by itself and was spraying water down the back of the machine causing the cutout switch to activate. To fix this is simple, remove the top cover of the machine and replace the pipe with a stronger clip than the OEM one.

Patrick
January 2016

A thousand thanks, I tilted it and watched the water draining onto a towel and now it's working 100%.

Patrick
January 2016

Thank you thank you thank you

Sean
October 2015

Kelvinator KD12WW1 Initially the machine was flashing the Intensive key and the warning buzzer was sounding and would not start or fill. Read the manual and it reads, 'overfilled." Tilted the machine backwards for about 2 or 3 minutes and about 2 litres of water came out the back. Stood it back up and it was working perfectly again! Yay! Thanks to all! Bill - Cape Town

Bill
August 2015

My machine gives no error code but doesn't select a program to wash. What now

Vincent
December 2013

Kelvinator dishwasher Kd14ss buttons not working

Leoni
December 2013

E1 keeps on coming up.what can I do??

kobus
May 2013

Hi all, Thank you so much for putting this question out here. I have had the same error 4 and not been able to clear it. I followed the tilt 45 deg back and a lot of water came out the bottom. when I plugged it back in now it is working beautifully. Thank you for all your answers and the advise about the towels. Have an awesome day.

Karen
January 2013

An S with a jug above the star means you need to add salt if you remove the bottom tray you will find to the left hand side a kind of knob you can open using your hands, open this and fill dish washer salt, Not table salt. Normally a bag would do. Close it and the sign will be gone on the next wash. Please note adjust the dispenser to your hardness of your water..

Leigh South Africa
November 2012

Thanks tilted it back at a forty five degree angle and alls well.

Thanks guys..

Leigh
November 2012

"malfunction of temperature sensor or of heating element".

Johan
June 2012

Opened mine up today, it's not a design flaw. Just tilt it and you will be fine. If it's happening often you are packing your dishwasher incorrectly and with too many items, I.e. catching too much water which then drips down and a resultant excess water volume. Also, your machine might not be draining properly, I.e. dirty filter at the bottom.

Imam
December 2011

Can anyone tell me what is the star sign at bottom left corner of display window means?

David
December 2011

Hi we are having the same error, we have tried tipping it but nothing comes out and still get the error. Any other advice?

gill
August 2011

Dishwasher is showing an S with a jug sign and not allowing me to select a program to wash.

chris
January 2010

Our machine is just over 2 years old (1 month out of warrantee) and we've been needing to drain it this way every 6 weeks or so for about 6 months now (as instructed by Kelvinator). It finally gave up and we could not get rid of the error code about a week ago. Kelvinator sent out a tech today (R 350) who replaced a pipe with a 2nd hand pipe (no charge) and let us know that this happens because of a factory fault. While the tech had the machine opened up we noticed that all the water does not drain effectively and pools in a recess at the bottom of the machine. This recess is evidently not rust proof. The tech let us know that this is a design flaw with the machine - the service manager denies this. We don't mind draining it every once in a while but are very concerned about the rusting water recess. We've escalated to the national service manager and will update you on their response.

Tracey
October 2009

Thanks very much for the advice. It really helped, am still waiting for Kelvinator to get back to me...

Frogg.
July 2009

Thanks everyone. Just fixed my E4 problem using your advice. Unfortunately did not read the tip about outting down towels so had to do a bit of mopping up.

Dazzle
March 2009

first i tried topping up salt, 1 packet then another cause it still beeped with E4 error code. next i tilted dishwasher backwards for about 5 minutes and it is working as normal now.... thanks for the advice ... it was so hard getting this information as i've lost the manual and googled but this site was pretty good in helping me out!! Thanks a million dude.

OJL
February 2009

I had the same problrm. THIS IS BRILLIANT it is working .

Eswiz
December 2008

You are a LEGEND! You saved me 100's of rands!

A tip for others who have this problem: put towels under the dishwasher as it leaks quite a bit of water. Keep it tilted for about 2 minutes and then it works.

THANKS!!!!!!!!!!!!!

Aimee
December 2008

Thanks for this advise. Just tried your trick of tilting dishwater slightly back and it works 100%
tx
Cape Town

Cape Town
July 2008

I had the same problem. I tilted it slightly back, and turned the water supply 1/2 closed. never given the prob again

Zayin
June 2008