My GHD straighteners are dead. it's not the plug as I have changed the fuse but there's no light or heat at all from them. What do you think it could be?
Fixed the girls crackling GHD...burnt contacts on switch...took apart and scraped them with a small screwdriver...electronics repair could do it also.
Jim
February 2016
just changed the thermal fuse in my ghd and it still wont work
Barbara o dowd
November 2013
my GHDs were beeping and wouldn't heat up but sometimes would after awhile> I looked on this site and thought it was the fuse. But after checking on the official ghd web site it stated that this was commonly reported as a fault when it is in fact a safety feature if the ghds are stored in a cold room or on a cold suface I follwed the advice on the web and they are now fine. I now keep them stored in an oven mitt. It also solved the puzzle as to why they worked fine when in spain as I had kept them in a place where the sun was shining!!
Cath
May 2013
My ghd want stop flashing and not heating up the best wat can I do to fix it
Bec
April 2013
My ghd don't turn on, Iv changed the fuse in the plug so it isn't that.
Thank you
Rachel
December 2012
my ghds switch on as normal, heat up then after approximately 5 secs they crackle, then pop and completely go off, i have changed the thermal fuse but still the same thing occurs, what could this be?
jackie tilley
January 2012
All these problems are common and can be fixed! Copy and paste this: GHD REPAIRS! BROKEN OR FAULTY, THEY CAN BE REPAIRED! on eBay and I can fix them for you!
Trev
July 2011
my straighterns have gone white behind the plates, well.. thats like the bit you hold when your doing your hair, why could they have gone white? is there something wrong with them?
Hannah
May 2010
Hi my ghd straighteners when turned on start flashing instead of going green
valerie
January 2010
when i turn mine on the red light beebs all the time and not heating up.Can anyone help?
emma
January 2010
I have a ghd that worked for a month however there is no power tested the cable is fine what else can it be?
Larnie
November 2008
mine have gone the same and ive been told its the heat fuse that needs replacing,they are been repaired now.
jule
September 2008
www.ghdspares.com for repairs or spare parts on ghd irons, It sounds like the problem could be the thermal fuse or the power cable, both are available from www.ghdspares.com for little money, may be worth using their repair service so they can have a look at them for you.
Marvin
July 2008
Fuse available from www.rswww.co.uk for a few pence
Brett
November 2007
there is a thermal fuse located under the ceramic plate in the control section of this straightner. unscrew the switch /led plate and you will see a pcb. the pcb is marked with the connections for the heater (white wires) and the fuse (brown wires) a simple test with a multimeter or similar will tell you if the fuse has blown. cant tell you if this part is available from ghd. have the same problem will update you when i find out. DO NOT ATTEMPT TO BYPASS THIS FUSE. IT IS A SAFETY DEVICE !! also it goes without ssaying make sure it is disconnected from the mains !!!
andy
June 2007
WARNING!!- ill give you some good advice, DON'T SEND YOUR GHD'S TO TONY M- i contacted him because my ghds wernt working properly and i was realy desperate to get them fixed so i contacted him and he told me that he would be able to fix them and gave me his address to send them to him so i posted my ghds to him and i sent the money for them to be fixed to his bank acount about a month ago and ive not heared from him since- ive sent him a number of e-mails but ive heard nothing from him and im so piss*d off that ive lost ghds as well as £25, i feal so st*pid that i sent them to him now but im just writing this so that you are more aware about who you send your ghd's to !!!!!
XXD.SXX
November 2006
hi there .there is a slip ring connection and you can have problems with this conection ..i can check and alter this lead..contact me on mrfire@fsmail.net
tony m
October 2006
Hi Sandra, i recently repaired a set of remington straighteners with a similar fault. The cable flexes a lot where it goes into the straighteners and this causes the wires to break inside the insulation. GHD straighteners however are normally designed to take this into account with a swivel cable connection to avoid this problem. If its not a broken wire then there could be a thermal fuse inside them which has gone. hope this helps.. if you need any more info you can reach me on customcalibraboy@aol.com
howtomendit.com for free repair help, information and advice.
