Recent: Safely remove screen protector from a Macbook Air?

Mend > Sewing Machines

Mend Bernina 2000de Runs Control Switch

bernina serger 2000de runs without foot control?

My serger starts serging as soon as I use the power switch, even without foot control. It only stops when I open the serger looper cover. In the servicing manual I was reading that the pcb could be damaged. Does any body know who could repair it?

issyquilts
September 2008
Undo the foot control and see if there is a capacitor inside, it looks like a big fuse, if there is then discard it because you don't need it, it has probably blown.

drivewithken@blueyonder.co.uk
September 2008

Automatic Answer

We may have found other answers which could help you.

Click here for Runs Control Switch

Related Questions ...

Mend error message checked
2

Miele G1222 series dishwasher F14 error message?

Hello, I am getting a F14 error on My Miele G1222 series dishwasher and believe I have checked the most common... [Read more]
Mend switch passenger side
2

how can i fix my heater/air con on my peugeot 306?

if I switch on the air con the passenger side works but the driver side does not and the driver side runs hot... [Read more]
Mend citroen radio repair
3

How to fix radio in my 96 Citroen ZX?

How do I register the radio in my Citroen ZX,I have the code No. which works but when I switch either the ca... [Read more]
Mend help problem started
1

Piaggio X9 250 Honda Engine?

Hi, Help anybody. Any Einstein out there. This problem started when not used scooter for 5 month. Always i... [Read more]
Mend water working properly
2

water ?

Carver Crystal Water flow not working properly. Connection: Operated by Whale pressure switch in the cold IN... [Read more]
Mend main working changing
1

Neff U1661 main oven not working - controller or thermostat perhaps?

Hi When changing the main oven bulbs I managed to somehow create a short which resulted in a bang/pop when tur... [Read more]
Mend control board switch
2

Hoover TV630 - connections to timer?

Have replaced the control board successfully, following a fault with the ON switch. However, accidentally the ... [Read more]
Mend problems runs fine
3

Amish heater problems?

I have an Heat Surge heater that runs fine for 5 minutes than shuts down, Heat, fan and lights all go off. Ho... [Read more]
Mend 100 previous owner
1

yamaha aerox yq 100cc electric problem?

i braught a yamaha yq 100 aerox and the previous owner has put a stem and handle bar conversion kit and a blue... [Read more]
Mend boiler thermostat heating
2

Micron 60FF snag (Glow Worm)?

Hi all. Micron 60FF playing up. Boiler works fine but ignores the thermostats and runs almost continuously u... [Read more]
Mend runs switch speed
2

how can I fix my mobility scooter?

my mobility scooter runs very slowly, the switch to increase the speed does not work, although it still clicks... [Read more]
Mend dishwasher drain pump fault
1

Control lights go out and drain pump runs?

Zanussi ZSF 2440 When connected and started the machine fills, as usual, however when that phase stops all con... [Read more]
Mend cold start morning
3

2004 alhambra tdi (auy engine) cold start fault?

in the morning car will fire for a spilt second then cuts out then i turn it over for about 10 to 15 seconds a... [Read more]
Mend ford ka engine running problem
1

ford ka running problems?

hi my y reg ford ka 1.3 endura has a running problem.when its started from cold it revs and picks up fine,when... [Read more]
Mend control model serial
2

repair/replace speed control module on my Kenwood chef model A701 ?

Serial No 228993. this machine will no longer operate at lower speed settings and runs from switch on at maxi... [Read more]

How to mend ...

Find out how to mend just about anything howtomendit.com for free repair help, information and advice.
Mend Sewing Machines ...