Recent: Fix food processor motor?

Mend Sportcraft Gym/Fitness Equipment

Mend Leisure Equipment, Gym/Fitness Equipment
Find out how to mend it for free.

Ask Question
Mend Leisure Equipment, Gym/Fitness Equipment
Free repair help for Sportcraft gym/fitness equipment

Mend > Gym/Fitness Equipment

Mend Sportcraft Turn Beeps Start

How can I fix my sportcraft TX 4.9 tredmill?

I turn on the tredmill and set the speed and it beeps to start and does not start. it counts to 10 seconds then shuts off, and the speed goes to 3.

renee rosenquist
October 2007
If you have error code 7 on Sportcraft TX 4.9 try pushing stop and mode remove key and replace while still holding the 2 buttons and hold 30 seconds or longer. Just tried with mine and screen reset.

LarryD
December 2017
I have tx 4.9 sportcraft tradmill not running shows only 7 on display don't know how to reset phone called but nobody picks up out of business anyone can help appreciated send mail shamimahmed71 at g mail

Ahmed
January 2016
my tx 4.9 sport craft. it stopped with 23sec.left on the clock. now all the numbers shoe 8.all the way across. thanks i need help .can't buy a new one. call or text at 205 300 8363

John
November 2015
I'm looking for a good working display control board for a sportcraft TX 4.9 if anyone has one for sale , contact me at rrisner at hotmail.com

Rick
November 2013
The speed
sensor is connected to the frame of the treadmill near the drive pulley on the front right roller.Take the plastic case off , only 4 small screws , There is a
small magnet or two on a plastic disk over the roller - pull this plastic piece over to the edge of roller on the side of the pulley wheel. The sensor tip must be close to this wheel to work - turn it on now and it should work right

steve staton
January 2013
My tx 4.9 treadmil turns on but as doon ad it get hoing it changes the speed to 3 n then turns off...plz help

tee
March 2012
I have turned on my treadmill and the it's plugged up in the wall but it will not turn on.

Sandy
May 2010
My sportcraft wasn't working wouldn't turn on and I checked the fuse which is located at the front of the the unit. Also just an inch and a 1/2 away is the on/off switch. I have children and they like to play with things. Make sure that the switch is to on.

BlackStar
January 2010
see if timing wheel and senser on front spool are clean and that senser is lined up and tight. they sometimes get dirty. this can cause the senser not to read the timing wheel. also check the fuse could be bad. had same problem. so I pulled the center board from between the belt to clean and relube it. was checking spools for damage and found timing wheel and sensor on right hand side.

joe
December 2009
Called the support staff, they sold me bunch of parts that didn't solve anything. It's bad workmanship on Sportcraft's part. Treadmill sucks!

TreadMillGuy
September 2009
I have the same issue. Also the front roller is warped.

Seth
January 2009
I have the TX 4.9 tredmill, totally not running, the only digit I see on the display is the speed of 7..Any way I can reset that?
thanks

Stevenphoto
January 2009
Im having the same problem, if you fixed it could you please let me know how, thanks!

Amy
December 2007
Call Sportcraft (800) 526-0244. They have pretty good support services. They can walk you thru this problem and help you reset your treadmill. We had the same problem, but it was a couple of years ago, but the Sportcraft staff helped immensely.
Good Luck

Jennifer
November 2007

Automatic Answer

While you wait for answers, we may have found some information which could help you.

Click here for Turn Beeps Start

Mend Leisure Equipment, Gym/Fitness Equipment
Free repair help for Sportcraft gym/fitness equipment

How to mend ...

Find out how to mend just about anything howtomendit.com for free repair help, information and advice.
Mend Leisure Equipment, Gym/Fitness Equipment
Free repair help for Sportcraft gym/fitness equipment