aeg dishwasher fault?

David Dec 2010 that just worked for our AEG 40010 VI - it's purring away again! (for now) Thank you

Al
April 2017

Hi, i have an AEG 40010 dishwasher, suddenly stopped, the end of cycle or fault light if you like flashes twice, and beeps continuously, beeping stopped now though light still flashes twice, machine will not do anything other than light up the control panel, switched it on and off several times and reset it, but no joy, any thing i can do or is it the skip, thx

Ian
October 2016

David: Your recommendation seems to work fine also on our AEG Favorit 86080 VI. Thanks a heapp

Filip in Sweden
February 2013

water gushing out from the back to the front of machine I am thinking it is a hose comeing lose?

carol
October 2012

water dripped into tray from seal in water reservoir this results in .30 error showing.emptying tray gets the washer working but does not solve problem.am going to attempt to change seal but cant locate workshop manual.

charlie
June 2012

Hi
My AEG integrated dishwasher not showing light and not working, i have changed the fuse but still no success ?? reason

Andy
May 2012

This is to further the solutions in respect of the continual running of the pump motor. Whils tilting the machine at 45 degrees does temporarily solve the situation, it is dealing with the symptom and not the cause. In my case the cause was a build up of fat and other stuff in the aqua system and, more importantly, in the large rubber pipe running from the main body drain to the water pump. To fix this you have to renmove the pipes and wash them all out - a long job but a permanent solution for me!

Taffy
June 2011

I suspect the cause of the i30 error codes is a leaking pipe split or connection. Mopping up the water in the collecting tray which is designed to prevent flooding will only be a temporary fix. I had this problem and the fault was traced to the three way hose which was split.

£20 replacement has seemed to fix the problem for now!

Chas
April 2011

Thank you David Dec 2010 you are a star! just did the same to my integrated dishwasher and saved myself £75 plus vat call out charge to AEG.

Helen
February 2011

My AEG 40010 VI wouldn't work and was displaying a continuous flashing light on the running programme. had 3 intermediate audible signals and the end of programme light was flashing three times also. The manual talks about an anti-flood device. I had no idea where that was.
The D/W is built in and is difficult to get out so I took off the only panel I could. This is below the door and is secured by 6 screws. As I was taking the panel off water started coming out of one corner. I panicked and put a low tray under the corner. When I finally removed the front panel I could see that there was a drip tray that was full of water. I used a sponge to mop up the water.
I turned on the D/W and it started working!! I then stopped it, refitted the front panel and all was well.

I've had the D/W for 2 years, so hope it will be another 2 years before I have to do this again.

David
December 2010

My AEG FAVORIT dishwasher upper basket keeps being forced forward breaking the seal to the spray arm, I've tried turning down the water pressure but it still happens even fully loaded with pots. Any ideas?

Dec
October 2010

hi i have an aeg dishwasher and the 2 top end lights flash and the machine doesnt do anything any ideas

craig
June 2010

mY FAVORIT seems to work OK but makes a loud busing noise after the first few minutes (piumps out ok)

any ideas?

derek
April 2010

Wij hebben de ingebouwde favorit 65080 Vi.
Hij geeft code ,30 aan. Dit betekent "het beveiligingssysteem tegen wateroverlast is in werking getreden".
Hebben zelf water ingegooid en het apparaat spoelt dit wel weg, maar gaat niet verder met zijn programma. Ook al gereset. Wat kunnen wij nog meer doen?

Petra
December 2009

My dishwasher give the error 20 and not work
Aeg favorit 65060VI pnc911234938.01

clementina
December 2009

We have emptied out the water collected a couple of times, but every 2 washes the fault 30 will come up again. How do we find where the leak is coming from?? Thanks.

becky
November 2009

my dishwasher is running on cold even on hot washes.

marie
October 2009

to willh, we have same problem, have taken off front panel below door, but cant find where you siphon water from, can anyone help please?

sue
August 2009

freddy, great advice; i've just had a recurring i30 problem with my Favorit 65060 (built in) - the overflow first tripped about 5 months ago (after which I emptied the water collected underneath) and again 3 months ago, 1 month ago and then once every 3 washes - after some careful observation I realized it was the problem freddy describes - and, touch wood, the cleaning of the 'bagpipes' / pipe seems to have worked! A couple of notes others may find helpful 1) my d/w is built in, so taking it out was a pain, I took the front lower panel off below the door and syphoned out the water using a £1.29 hand syphon pump! 2) I think this problem is caused in part by not using salt, but only relying on the water softner in d/w tabs - this part of the d/w is "pre detergent" in the cycle, and I live in a hard water area so crud was mainly limescale... I'm going to use salt from now on.

willh
May 2009

Same problem as many others. "Anti-flood" device seeming to trip RCD in housefold. Have discovered that one of the hoses is spraying water out in small amounts. This would cause all the problems noted. Am currently finding out if it is the hoseclip being weak or the rubber perished. Also, signs of water on the bottom of the motor. Any such water would trip the RCD in the household. This is more likely than the "anti-flood device" switch being responsible. Also, anti-flooding does not seem to mean stopping an internal flood - it looks more like an anti kitchen-flooding device. A perfect way never to find out there is a leak until it is too late.

Barry Chaplin
May 2009

AEG Favorit 50730 Sensorlogic: Keeps running on continually, until we switch it off manually. Does not always dry, pots sometimes cold & wet, but washed.

Briandc
August 2008

on several of models the water reservoair , the plastic house on the left side must be cleaned, and the big hose in the bottom from reservoir to the center is filled with fat so the water fills to slowly and it runs over in the reservoir overflow hole and down in the bottom. this , little by little fills up the aqua stop sensor system. IThis causes water in the bottom of your machine and waterblock system to trig.

j troli
November 2007

Check the pipework ,as you look front on left hand side panal,
remove it (turn off power first) over time it fills with fats,remove plastic bag pipe set up and flush clean, then replace.hey presto.

freddy
June 2007

I am having the same issue - I'm concerned that just emptying out the water is only a short-term fix.
It seems to me that water is splashing out of the salt "canister" on the left hand side of the unit during the water-fill process. Should I try to fix this?

Graham
May 2007

Thanks for the advice Nick - saved me a call-out charge. Please note that you will probably get some water spilling out on to the floor when you tilt the dishwasher on its side.

Eric
November 2006

No not on hose but a float in the base of machine. Tilt washer on side to drain water out of base allow to dry and should cure thye fault 30 prob.

remember to disconect from the mains electricity before doing this

atb

nick

nick
December 2005