diplomat ADP8332?

Hi, I have a diplomat ADP 8332, the problem is that it isn't cleaning the dishes properly and the tablet never dissolves, it does pop out however. I have noticed a different tone when it's washing but everything else is normal ie washing, draining and it's getting hot.
Ta very much
Joe

Joe
April 2014

hi there can you please help and advise me on what to do? my dishwasher is showing f2 with rinse only botton light on - not flashing. cant seem to swithch on the machine. how do i amend the fault? or clear the error..... thanks for your help in advance.

HMP a lady in need.
December 2013

my dishwasher stops with the F3 fault indicator,
any ideas how I attempt to repair the machine ?

jane
March 2011

Hi I have the above dishwasher, I keep loosing the power to the dishwasher when I open and move the door as if there were a loose connection between the door and the unit, all the lights go out and I have no power, but when i open the door fully the lights turn back on, its only when i go to close the door to operate, any ideas and can it be fixed??
thanks

Ryan MALPASS
December 2010

How can I remove the drip tray? I have F2 Fault Code and apparently I need to find the root cause. Do I need to pull the dishwasher out from under the kitchen unit?

John
May 2010

I have a Apd 8332 dishwasher which now has a F2 fault after initially not pumping out the water.The machine will not now start at all only dislplay the F2 fault.I read above from all the comments above that I should empty the drip tray is that the metal base plate ,also I should empty the large container on the right hand side of the machine , what is correct ?

Al

al
March 2010

I have a fault code F7.

Also it is making an audible beep.

The only operation that can be made now is to switch it on an off. It does not respond to any other button pushes.

Help!

Brian
January 2010

where is the pump??

ly
September 2009

We have just experienced an FA audible error on our Diplomat ADP 8332 dishwasher...after pulling the dishwasher out and removing the low front panel we found the drip tray full of water. We tipped the dishwasher onto it's front and removed the drip tray and found a float pressure switch...it appears that once the drip tray is full the float switch activates and causes the FA fault (prevents the dishwasher from continuing) drain off your drip tray replace all covers and you should be good to go!!

Lizzie Hampson
September 2009

I have had similar problems, firstly got the FA alarm showing so I switched off the power, removed the front lower panel found no visible problems. Carefully lowered the dishwasher onto its front and removed the pump and pressure sensor and thoroughly cleaned them out. After replacing the parts I poured water into the bottom of the dishwashers and powerd back up to trial run. The water pump ran and removed the excess water from the bottom and the dishwasher seems to run but now I get the F4 alarm but the spay nozzles dont seem to be working or washing. The drainage and water hoses are fine and not kinked??
Any one help!!!

Paul
August 2009

Where is the F4 pressure switch located?

John C
June 2009

Manual for ADP 8332 is on ebay

John
June 2009

fault code f4 came up on my dishwasher i took it apart(4 screws on front panel at the bottom and onthe panel underneath) and took the pressure switch off-a black plastic part with a plastic mesh and found it greasy and sticking. f4 is a drain pump code and if the pressure switch is sticking the machine thinks the pump has not drained correctly and there is still too much water in the machine. clean thoroughly and/or replace. hope this helps.

keith
December 2008

hello i had the same problem with water in the bottom and i drained it all out and set it up outside (with my outside tap) and you have to unscrew the bottom and check for loose connections or split pipes in my case it was a split pipe but all the symtoms where the resetting of your d/w so if you are having the same trouble look out for this

alec
September 2008

I to have FA but we took the thing to bits, emptied the drip tay and it cleared. Still none the wiser what FA means

jan
March 2008

why does my dishes come out smeary, when they have gone through a wash cycle in my dishwasher

caraline.attfield@ntlworld.com
October 2007

Is fault F4 easy to cure or does the dishwasher need replacing on Diplomat ADP 8332 ?

S Dagg
August 2007

Hi, Fault Codes F1 Faulty NTC
F2 Water leaking underneath
F3 Heating fault
F4 Drain pump failure
F6 No water supply
F7 Flow meter failure
F8 Overfilling
F9 Water valve not closing
Hope this helps

Dan
January 2005

Steve I have a similar problem. Error FA. Can't find the manual, but have posted a question asking if anyone has one to find out what the error codes mean. (to clear the error off, hold down the right hand start button).

Brian
January 2005