citadel xr2+ tamper mode?

Hi
It's me again! I have a new problem now and I was wondering if you could help seen as you did last time.
When I set my alarm, the pir sensors in the rooms do pick you up so I know they are working. However, once the alarm has set, if I walk into a room the alarm does not go off until about 1hr 15 min later!! When it does eventually set off, it turns straight off when I key in my code and does show the correct room that I did go in earlier. The tamper light shows on the keyboard though. Any ideas!

Alex
December 2013

Thnx for the thanks Alex :)

e manno
October 2013

e manno,did the work,dont take this the wrong way,hope we never see you here again !!mean that in the nicest post way :-)

gts
October 2013

Yes you did thanks. Ill remember this site, might need more help in the future! :)

Alex
October 2013

will know you in future alex,be well,hope you fixed your prob

gts
October 2013

Hi
That's alright. Like I said, it's a great site and it is nice to know there are people that will help out.
Thanks

Alex
October 2013

am not a bad guy,(just don't ask my ex ) :-)

gts
October 2013

at least you thanked e manno,witch is more than most people do,and for that ,I thank you :-)

gts
October 2013

I did apologise mate,and we all know our stuff here,we have among us about,and I hate to say it,140, years experience all am admitting to is 45:-)
I don't sleep much so I stay in line and reply to anyone who needs my help,i do forget there are NORMAL people out there who do sleep,sorry again,we are really here to help your guys out

gts
October 2013

Gts - I appreciate your help and do thank you very much for that. I was a little taken aback though when only a few hours after I posted my question I got accused of wasting time and not having any manners. Surely you must understand that and would feel the same as I did had it been the other way around. For you also to keep going on about it after you know I am genuine too is not nice.
It wasn't that I didn't have the manners to reply, I just didn't expect an answer so quickly so only noticed the answer when I checked a COUPLE of hours later.
This site is good, and you know your stuff which is great but if you keep presuming everyone is not genuine and being very 'unkind' with your words then you might as well shut the site down seen as the 'genuine' people are not trusted.
I did nothing wrong and do not expect to be spoke to that way, that's all I'm saying.
That aside, I do thank you for your help.

E manno - thanks for your help, it was appreciated

Alex
October 2013

truth to be told,i thought your where extracting the the urine mate ,as my friend e manno said some people come on here just to wind us up ,I apologise if I got you wrong

gts
October 2013

and I don't need your apologie mate,just common curtsey will do

gts
October 2013

well you see alex,how are we to know your not by your comp?i like most of the guys on hear sit on our comp to help out people like you,so,please keep your sarcasm to yourself,and since you did NOT have the manners to reply,how can I help you out in any way ,never judge anyone by your own bad manners ,and if you don't like this reply,tuff ,am not on hear to make friends but to help people out,witch I do often ,to us an alarm is a serious thing,if a user system not work then we do our best to help,your talk is on the level of your intellect mate

gts
October 2013

Tamper light lit means you have accessed engineering.

All the best, but remember don't short any wire's,remove and replace one wire at a time.the terminals will be clearly marked on new beam.

If for some reason you do get a tamper alert when you remove the beams cover,then simply go to your keypad and enter your user code.

That will silence the alert then carry on with your replacement.

e manno
October 2013

Hi

I've tried pressing prog and then entering 9999 and I think it works. The alarm did sound but then I put in my code to stop it and it seems that I am now able to work it. I just have one light lit up next to 'tamper'. Hopefully that's it now, thanks for your help.

Alex

Alex
October 2013

No probs Alex.

For you to enter into a conversation on here with gts and I means you are genuine.

We think that most posts lately are of the none genuine type,hence our replies.

Good luck and feel free to ask us any more advice regarding your system.

e manno
October 2013

I will have I try it tomorrow now as its not possible to do it at the moment. Thanks very much. I will post tomorrow to let you know how I got on :)

Alex
October 2013

Ok that's great, thank you very much for your time. I will try that and hopefully it will work :)
Alex

Alex
October 2013

9999 is the default engineering code.

If I don't work then ask the engineer who last had contact with your alarm for the engineering code which he will of changed to one of his own.

The engineering code will put the panel into engineering which in turn will cancel out the series tamper circuit allowing you to remove said pir without setting off a tamper alert.

When you wish to exit engineering mode then press (RESET)and the system will return to day mode.

Don't allow any of the wiring cores to touch each other or you stand a good chance of blowing the AUX fuse within the panel.

e manno
October 2013

At the keypad press (PROG) then enter 9999.
Tell me what happens.

e manno
October 2013

I know you are serious and so am I!! When did I say it was a trick question. I only posted the question this afternoon! I'm sorry for not knowing that I had to wait for an immediate answer! I presumed it was a forum! Maybe I shall not ask for help in the future, it seems if you do, you get your head bitten off! The sad thing is, I really did appreciate your help :(

Alex
October 2013

It's not a trick question.
I'm serious : you knowing the engineering code will help me to help you and instruct you how to.

Gts is right though,being ignored when offering help is most irritating.

There's an add answer form below to enter additional information .

e manno
October 2013

Gts - I apologise that I do not sit by my computer in order to reply to people within seconds of them helping me out but I do have other things to occupy me in my life! You obviously don't if all you can do is be nasty to people and not offer help whatsoever. That's obviously what stimulates your mind!

E manno - I do appreciate your answer. I do not have a engineering code. Would I have ever had this? In a book or anything?
Thanks

Alex
October 2013

tell you what alex,since you have not the manners to reply to e manno,call an engineer out pay lots of dosh,then maby you will appreciate this free advice site that is run by proffessionals

gts
October 2013

Do you have the engineering code?.

e manno
October 2013