my tumble dryer (Beko DRVS62w) is not working properly!?

put new felt strip around drum plus clips and belt, new belt. put back together but is sparking at connections top right of machine even when just plugged in and not using. all connections were disconnected including 2 on back panel could this cause sparking if put back wrong. Works and heats up but sparks so had to turn off

Jackie
February 2016

Unplug the dryer.Pop your head inside the drum, at the bottom (6 o clock ) just under the removable filter you will find a cover containing 2 metal strips, remove this by means of unscrewing the 2 recessed screws, turn it around and you are likely to find it clogged up with fluff. Clean this off with a small brush, re-assemble. Just may do the trick, mine did!

Stuart A
April 2015

Hi there I've just got I beko dryer from my friend he used to keep it in the shed but when I switch it on it trips the fuse box in the house do u know what the problem is

John
March 2015

My dryer keeps saying to clean filter but there is nothing to clean I have checked for blockages but there is nothing

Debbie
February 2015

Drum not rotating

Lorna
January 2015

I have changed my belt and drum bearing now my dryer won't heat up inside and the heating element keeps turning it's self off. Any help would be great

vicki
March 2014

The filter light keeps coming on, when checking the one and only filter the ligh keeps coming on please could you help with this fault thank you

Barbara
March 2013

my beko tumbledryer is so noisy ive tried putting in a heavy load i ve tried a light load ive tried stripping the machine and clean it with no luck ive also checked to make sure the machine is level please help someone

kerry
February 2013

Hi thx for that i cleaned the old vent hose and now its drying again
Cheers
Nigel

Nigel Meakin
January 2013

There is a design fault with the rear of the drum... at the back of the drum there is a mild steel plate with holes and then there is a round heavy duty disc with spigots on it which locate from the casing to the drum.

After 1 years mild use and never overloading the machine the drum on its stop-go in the other direction has worn this plates holes to an oval shape which makes the large belt slack and then the belt snaps. [caution on overheating].

I have repaired using (high temp) liquid metal weld on the spigots and refitted to the drum. Left for 24 hours to set. The machine now has been running for 18 months with no problems.


Remember to wipe the chrome sensor just inside the door with vinegar.

RICHARD STARTUP
December 2012

The drum does not go around

Darren
June 2012

I also had the same syptomns, but there was no blockage or lint in my pipe......on a hunch i unscrewed the sensir bar ( once unplugged from the mains) and found it to be packed with lint behind it. i disconected it carefully by the 2 spade connectors, removed the lint and gave it a wipe and it now works as new again.

Mr Kris!
October 2011

Our new Beko tumble dryer wouldn't dry either. The remedy was simple and embarrassing. I had connected the new dryer to the old vent hose, but on using the new hose and cleaning the vent outlet thoroughly it now works fine. I concluded that it wasn't venting properly and because of that it upset the sensors.

Richard
May 2011

hi, my beko is not heating up BUT it is not the heating element in as such as every thing is working as it should be, when tested, but not getting hot. any idea before i dump it as a really bad investment??

nikki
April 2011

my tumble dryer keeps saying clean filter which i have done and its still not working

washerwoman
March 2011

put a full load of wet heavy bath towels in and try it.As you open the door at 6 o clock position there is 2 stainless bars.these are the sensors for the auto drying.if there isn't contact with these bars during the dry cycle it stops as it thinks everything is dry.by testing with full wet bath towels will tell you if the sensing circuit is working.too smaller loads of synthetics and nylons can have the effect of stopping before they dry.I think its in the fault finding page in the manual??

ck
February 2010