Recent: Home max fs506x?

Mend > Blenders/Mixers

Mend Kenwood A717 Motor Chef

faulty motor Kenwood chef major A 717?

we have smoke coming from the mixer and the motor speed controller doesn't work.Any suggestions please and thank you.

ann
November 2009
My model A901 Kenwood chef began to smoke and give off an acrid buring electrics smell

dean
December 2009
capacitor has gone. try kenwoodchefusedmixersandspares. 07507400101

mick
November 2009

Automatic Answer

We may have found other answers which could help you.

Click here for Motor Kenwood Chef

Related Questions ...

Mend mixer Kenwood motor
1

kenwood chef km200 mixer?

how do I remove the motor to fix the broken pulley spigot. I cannot find a way to separate the top half of mac... [Read more]
Mend speed kenwood motor
3

How can I fix slow speed on Kenwood a701a?

I recently replaced the 450 ohm resistor on kenwood chef a701a. the motor is now running but only on no load, ... [Read more]
Mend kenwood motor gearbox
1

im trying to fix a kenwood chef mixer a703c ,motor goes gearbox seems to wo?

i have the kenwood a703c the dog clutch doesnt seem to wind right down on top of the large plastic gear .
Mend motor speed works
2

kenwood chef A701 kitchen mixer?

Motor runs OK speed control works OK, until the motor is put under increased load and it cannot cope, checked ... [Read more]
Mend kenwood speed off
9

Kenwood Chef - speed knob - how do I get it off?

I am trying to replace the motor in my (very old) Kenwood Chef with a motor from another (even older) Kenwood ... [Read more]
Mend mixer top cover
1

How do I get the top cover off the Kenwood Chef 901A?

I am following the notes given by "kickstart" in December 2011 for dismantling the motor from our Kewood 901A ... [Read more]
Mend mixer motor speed controller
2

How to adjust the speed controller on Kenwood Chef A901B mixer?

Can some one please advise me on adjusting the speed controller on KENWOOD CHEF A901B Mixer. I tried to set it... [Read more]
Mend kenwood drive belt
2

Kenwood Chef 901 Drive belt?

The drive belt on my Chef 901< (from the motor to the drive head), rises slightly when the motor is switched o... [Read more]
Mend kenwood chef mixer
2

How can I fix my Kenwood Chef Mixer?

The motor of my kenwood Chef A701A (30 years old!) mixer no longer drives the planetary action of the beater. ... [Read more]
Mend control model serial
2

repair/replace speed control module on my Kenwood chef model A701 ?

Serial No 228993. this machine will no longer operate at lower speed settings and runs from switch on at maxi... [Read more]
Mend model mixer speed
1

Kenwood Chef model 701A?

With K beater fitted, mixer was on low speed and suddenly there was a screeching noise. beater then made a cl... [Read more]
Mend Kenwood PCB Mixer
2

Repairing Kenwood Chef A901?

My Kenwood motor control circuit failed so I bought a new pcb replacement and fitted it. Problem is the motor ... [Read more]
Mend Kenwood Repair Motor
1

how can i fix the motor problem in my kenwood chef A901?

my kenwood chef A901 keeps missing on low speeds upto3 then smooths out the faster it goes. have checked brus... [Read more]
Mend How to mend it?
1

My Kenwood Chef KM300 is dead =( ?

hello everyone! now this is what happened... its not actually my kenwood.. its my moms, she forgot that her ta... [Read more]
Mend How to mend it?
3

Kenwood Chef A 901 bang and smoke?

I use my Kenwood Chef A 901 Serial # 0840909 for mixing boilies which is quite a heavy job I presume It is 50... [Read more]

How to mend ...

Find out how to mend just about anything howtomendit.com for free repair help, information and advice.
Mend Blenders/Mixers ...