CTD00 Hotpoint tumble dryer trips circuit breaker?

The ctd00 has a problem with creapage across the mica sheets which get contaminated with dust and water over time in my opinion it is a design flaw which they have corrected on later models by cutting away the effected area but this will eventually lead to the element falling down and shorting out again

bob
December 2014

Oh I forgot to check the pump just take off the plastic pipe at the top where it goes into the water collecter and it should be pumping water out.

Trev~ Hucknall
December 2012

Also it may be that the pump is not at its best or clogged up and so water is backing up, clean pump, foat switch or replace pump. Located at the back at the bottom at the end of the two pipes.

Trev~ Hucknall
December 2012

how do check electrical circuits breaker on a hotpoint dryer cdt85a.i have recently change the belt and i turn the machine on it trips the main circuit.What do i do now?

as moosa
July 2012

Thanks for the amazing advice. Our tumble dryer broke down two years ago so I put it in the garage to try to fix it. Two years of the wife moaning and 30seconds after reading this blog and it is fixed thanks so much

Simon
April 2012

Same happened to me after moving the machine from one room to another. Small amount of water found in bottom of fan/heater cover. Dried it out and hep presto, running fine.

rodout
August 2011

I have the same problem, have cleaned condenser again and again, taken off back housing to fan and heater, dried with hair dryer and replaced all. Turned on again, works for about an hour then same problem comes again with water in the housing. Fan & Heaters all appear to be working, airways clear etc.. But problem persists. Can anyone help???

AOR
March 2011

Thanks this answer is a god send. I thought i was gonna have to call an engineer out to solve the problem.

Rob
February 2011

This has been the worst 2 months of my life and then to top it off my dryer started tripping my circuits. My son has very bad allergies and I have to wash all beddings once a week. Without a dryer, his bedspread/duvet takes 4 days to dry.

I spent 20 minutes with a hairdryer and the problem is solved. We have snow out the wazoo, wet clothing everywhere...you get the picture. This advice just saved me 250 Euro/$300 US in Ireland. At Christmas. I'm about to cry. Thank you so much.

Very grateful expat
December 2010

hi i have a ctd00 hotpoint dryer and the empty light always on n it never has any water in it also it doesnt seem to be drying clothes

audrey hodgson
September 2010

Thank you, this is awesome advice! My wife was ready to throw it out, but 20 minutes later it's sorted! Brilliant.

Relieved of Wokingham
August 2010

As soon as I started reading this solution I remembered that it was the remedy used by the Hotpoint engineer sent around by the insurance company last time this happened to our machine. I also remember him telling me that it was one of the most common faults with this model of condensing-type dryer.

Anyway, I've just taken-off the cover hiding the fan and heater elements and dried everything off using my better half's hairdryer (just as Baz suggests), reassembled it all, and now it is working like a good 'un. Yay !. So that's a service engineer's callout charge saved at the least, and at the most five hundred quid saved for a new drier just before Christmas.

One thing -- the cover wasn't full of water but there was definitely a good couple of desertspoonfulls; enough for the spinning fan to spray copiously over the heater elements and cause the machine to trip the circuit-breaker in the fuse box when it started the hot-air cycle.

Thanks a lot for the fix, Baz.

Win
December 2009

This answer saved me at least £100 in a service call plus countless hours on the phone trying to arrange a service appointment - waiting around at the house all day for the technician! Thank you!

I applied the solution above (rinse the condenser unit, remove the cover for the heating element and let it dry) and the dryer is once again working perfectly.

Can't thank you enough!

Tyzer
April 2009

ive just found this info

its worked for me

This happened to me.

Your condenser unit on the front bottom left corner may be clogged up and causing water to back up around the fan and heating element behind the rear panel.
Take condenser unit out and give it a good clean removing as much fluff as possible.

If the heating element senses damp on it, then it will trip the electric.
The back panel which is at 45 degree angle on back. I took this off and sure enough there was water in there.
Wipe away all water and use an ever so slightly damp cloth to remove as much dust stuck to the metal as possible.
I used a hair dryer for about ten minutes fanning over the heating element and circular fan. Don't rush this. Take your time to make sure all signs of damp have been removed from heating element before putting the back panel back on.
After carrying out the above my machine worked fine and no longered trip electric.
It is a pain, but to prevent this problem happening I suggest cleaning condenser unit about once a week if you have alot of washing. Empty water panel after every two loads, maximum.

Good luck

BAZ
August 2008

IM HAVING EXACTLY THE SAME PROBLEM. PLEASE CAN SOMEONE HELP

BAZ
August 2008