how can i fix my whirlpool 6th sense washing machine?

When I start it, after removing left over water, the machine try to kick start, but the door light keep flashing and the door dose not lock at all...

Ugo
April 2017

My 6th Sense machine wont SPIN ..HELP.. One year old used once a week..?
Thanks..

Frank Dunne
March 2017

My washing machine has finished its cycle, but the door is locked. The door lock light will not turn off.

Mickm
January 2015

i have a problem ,my machine dont start , the light of door dont turn on , i select program , and green led fixed , but dont start

fernando jales
November 2014

Had the same problem, flashing door light and the washer would not start. I cleand the stator on the motor, which had become completely black, and yeah, that fixed it....

Ingo
August 2014

Hi my whirlpool 6th sense keeps stopping at spin and then this little red square that looks like a telephone touch pad comes up and it won't go into spin. I have checked that it is balanced. Any ideas as to what the problem could be?

Cheers

Therese
August 2014

Mines is now leaking any help

jon
December 2013

Replaced the bushes as per previous comments as the door light would not go off and the programmes not working. Once bushes replaced washing machine working as new. Many thanks for all the above advice.

Aubs
November 2013

my whirlpool 6th sense washing machine is turning off just after the beginning of the cycle. the screen turns green and then blank as if off. a few seconds later it tries again.

can anybody help??

Gary
December 2012

6th sense AWO/D 5506 1200, service light came on,then went dead! Checked fuse it's ok.Pressed reset, Left un-plugged for a while,M/C wont do anything.Apart from checking motor and brushes any ideas??

HAYLEY
December 2012

Guys, same problem, door open sign is on and won't allow me to wash. If i slam the door ridiculously hard it sometimes works but only occasionally. I have replaced the interlock, door seal(as it as a hole in it), and brushes and still the same problem.

Any clues out there???????

Thanks guys.

Jo
April 2012

Also just cleaned the spindle and brushes with steel wool and metho and hey presto now working again thanks for the great advice

Dave
May 2011

Had the same fault on mine but not brushes
Checked them ok but had wear
Checked voltage to motor only 125 volts
Checked controller board and found dry joints
Re soldered
Job done works fine
Also replaced brushes after as they were worn
So did as I had machine apart hope it will last
Another 6 years

Jools1
April 2011

I have just had the same issue with our machine and I can say the Brushes on the motor were down to the end - replaced at cost of 15.95 and machine 100% working - brilliant

BTW - changing the Motors brushes was very easy - just remember to snap the little plastic retainers off the brush holder before fitting the unit - this keeps the brush in place when in the packet as its spring loaded -

Took longer to clean the dirt build up behind the machine than it did to change the brushes

Many thanks

Billyboy
January 2011

Had the same thing on mine. Removed motor, cleaned copper bowl but no good. I guess replacing brushes is next option.

WanderingOz
December 2010

hi rob can u tell me what was wrong with your machine as mine is doing the same

mick
September 2010

clean bushes i just done it and it works thanks big dave u saved me some cash

graham ward
July 2010

whirlpool awm 8103/s
door light flashes at start of cycle when motor is supposed to kick in.
just fixed it thanks to a post about the motor brushes.
the brushes didnt look that bad but the copper spindle that they touch was black and dirty.
i simply cleaned mine with some steel wool until you could see the coper colour again and hey presto, sorted.
if you have a multimeter handy you can also test across the brushes for continuity to confirm there is a circuit.
motor was easy to get out once the single bolt was removed but beware, it is heavy if you are lay on your side and the insides of the case can be quite sharp.
also, mind your fingers when removing/refiting the belt.
i put mine on the same way you thread a bicycle chain onto its sprockets.
thanks again to whoever you were for the tip.
a great help and saved me a fortune in wrong parts.
cheers

big dave
July 2010

my machein wont start the machein is making a clicking sound then the doot light flahes

mrs bagshaw
November 2009

The same thing has just happened to my machine tonight and i was wondering how you got on and how did you fix it. It would be great if could let me know just before i phone for a service man and get another unwanted bill....

jim
March 2009

Definate repair on my machine was the motor brushes. They cost about £20. Hope this helps anyone out who has the same grief. Cheers.

big rich
March 2008

I too have this fault, at switch on the timer clunks round, it pumps out any water in the machine (lasts 2-3 secs), It then begins to fill. This only lasts about 2 -3 secs then stops with door open light flashing. Am 99.9% door switch is ok. If left for a couple of mins it tries again but only once. This is the same for all wash cycles. Tried on gentle spin and it did the same. Now strongly suspect the motor (which should run ( i think) at the point of faliure). Ran out of time last night so will investigate further tonight and update accordingly.

Big Rich
March 2008

thanks dan - i'll check your site out later and let you know how i get on. thanks again in advance and with fingers crossed!

rob
February 2008

Only way to test interlock is to replace with a known good unit.
They arent too dear, round a tenner online.
Check out my site for info: www.2ndwave.co.uk/manual.html

dan
February 2008