How to mend Help Machine Changed

1

servis m6011 w/machine,no power or lights when on/off switched on??????

plz help!!!!servis m6011 no power to machine when u press on/off switch, no lights come on, dead as a doo doo!... [Read more]

2

hotpoint wmm53 not pumping water?

my washing machine does not drain hence no spin.Checked for blockages including filter,changed pump pcb was bl... [Read more]

3

problem with tention on a new home machine model JD1722?

Help I'm having problems with the bottom tention stitch it keeps forming little loops every inch or so, any Id... [Read more]

1

hotpointfirst edition800?

my machine is filling up with water and then draining again. i have changed the brushed and the drum still isn... [Read more]

1

Why isn't my Toyota Quilt 50 catching the bobbin thread?

My two year old machine has worked reasonably well and had quite heavy use. Yesterday, it developed a trick wh... [Read more]

1

i keep getting page unavailable when i try to connect?

I HAVE TRIED TO OPEN A PAGE AND KEEP GETTING PAGE UNAVAILABLE WHEN I TRY, I HAVE JUST CHANGED TO VIRGIN BROADB... [Read more]

1

my hotpoint tdc32 does not start help?

the machine does not start i have changed the fuse what could it be was working fine i stop the dryer because ... [Read more]

1

Can the needle position be changed on my 940 viking?

I have inherited a Viking sewing machine model 940. I can't figure out how to change the needel position. Can ... [Read more]

1

my fuel injection light is on in my Fiat ducato 2.8jtd,?

The diagnostic machine says that there is a fault between ecu and 2nd fan? But the 2nd fan works if you earth ... [Read more]

1

Hotpoint Aquarius - WF210 - RED LIGHTS FLASHING (on/off - etc)?

Please help me, I have an intermittent fault with my washing machine. Every now and then the machine will ... [Read more]

1

re: zig zag [Brothers Boutique 771] serial#c25187945?

I tried the neede and it did not move,but I changed the needle anyway, it was slightly bent. I put it in corre... [Read more]

2

Help ! IBM 600e, cannot find Hard drive?

I have a 600e, was working 100%, changed HD (2!, Tosh30gb and Hitachi 40gb).. NOW, cannot see HD, (either) Pre... [Read more]

1

bosch maxx wfl2260 changing brushes?

Hi, I changed the brushes in my machine by removing the motor from the bottom as this seemed to be the only wa... [Read more]

5

fault codes for indesit evolution 1400 we 14?

Had a repley to my Q about fault code F02, Many Thanks. But now the machine has changed its mind and keeps com... [Read more]

1

WM31 Help! Changed suspension but the knocking is still there??

I have changed both suspension rods but now I have a sneaky feeling that it may be the bearings that are makin... [Read more]

2

no water?

hi i have a hotpoint ultima 1400 machine it goes through the cycles but i have no water, i changed the inlet v... [Read more]

1

creda tumble dryer capacitor for motor failed again?

Six months ago my creda T602cw tumble dryer motor was trying to start,but could not if you turned the drum by ... [Read more]

1

tdc62p not heating up hotpoint?

i have changed the heater on the back of the machine it is the correct possision wires ect all looking good...... [Read more]

1

Cold water slow to fill?

I have a Kenmore series 70 washer. The cold water just dribbles into the machine taking it much longer to comp... [Read more]

2

indesit w113 help?

I have an indesit w113 that must have been the worst one off the production line. I recently changed the beari... [Read more]