Recent: Trying to find lawn mower part- Power Devil PDG4037R?

Mend Scantronic 9651 Home Alarm Systems

Mend Security Systems, Home Alarm Systems
Find out how to mend it for free.
Ask Question
Mend Security Systems, Home Alarm Systems
Mend repair fix Scantronic 9651 home alarm systems

Related Categories

Mend Car Alarm Systems
Car Alarm Systems

Mend > Home Alarm Systems

Mend Security Systems, Home Alarm Systems

How can i wire my bell box?

Hi
I replaced my scantronic 9450 alarm panel with scantronic 9651.I have got the pirs and door contacts all woking ok.I cannot get the bellbox to work.It is about 25 years old but still looks good and was working properly before i disconnected it.It was installed by an alarm company CSS and the bell has the company logo (CSS) on it so i do not know what make it is.
The way i wired the bell from panel is
Red from 12v aux to + off on bell
Black from OV to - hold on bell
Blue from TR to tamper on bell
Yellow from OP1 to bell on bell
Orange from OP2 to strobe on bell
In the bell there is a resistor between Red + off and Yellow bell.
The two small lights are flashing on the bell as if it is working normally,but it keeps bleeping quietly every few minutes and does not activate with the alarm.
There is also an other connection on the bell marked set but is not wired to anything.
I also notice that the tamper switch has never been wired to any thing by the company originally.
I know this sounds complicated so i hope someone
out there can help.Any help would be greatly
appreciated.
Thanks in advance

Shauki
March 2016
Scantronic 9651Security Systems, Home Alarm SystemsBox Alarm Panel
Hi gts
Just to let u know,got the alarm working like a dream,replaced the pirs as well so hopefully it should last me a few years.
Thanks for all your help.now for that creaking floorboard on top of the stairs wheres my hammer??????

shauki
April 2016
no bend the lever on the micro switch to make sure when you put the blue cover on the blue button is pressed down by the bell box cover

gts
March 2016
Now I get it. You are talking about the new box when you are talking about moving and bending switch and white cover.
Confusion over.

Shauki
March 2016
ah the panel must be prog for resis in the units,no prob buy new bell box mate only a fool buys a battery for a unit that old he colours dont matter,we all use our own ,long as they go where they must:-)thank you for your reply ,if you fit our bell box you should be ok

gts
March 2016
Thank you for that gts.I have now got the bell to work and I do need the resistor in otherwise the bell rings continuously when connected up.Although when I took the bell down and wired on the bench next to the panel,it worked without the resistor. I wired it
yellow bell to op1
Orange strobe to op 2
Blue tpr to tamper
Red hold + to auxiliary +

The switch has never been wired to anything,so maybe moving it about might not make any difference.
It still clicking every few minutes but I think that is because the battery in the box needs changing,so I might end up buying another bell,as the battery costs ten to twelve pounds
including delivery and some bells are around twenty five pounds. your thoughts would be appreciated.

Shauki
March 2016
dump the resistor not needed

gts
March 2016
there is a clear cover under the blue one,i forgot about that

gts
March 2016
one more thing on the bell box the anti tamper micro switch has a lever ,you will need to carefully bend it push it a bit back and bend the lever so it takes up any space what i mean is push it up and back to bend it

gts
March 2016
we use the cqr multi box,now remove power from the panel mains and battery,remove all wires from the bell box on panel put white wire to the strobe connection on the panel,the blue wire to the bell input on the panel the red wire to the pos output on the panel the black wire to the neg output on the panel and finaly the yellow wire on the tamper return on the panel,then do the same in the multi box then all will be fine ,on the multi box fit the little wire from the battery onto the socket in bell box,then fit the blue cover then fit the outer cover,remove the little cap thats stuck to the inside of the cover,this is used to cover the screw that holds cover in place,then reconnect the battery inside panel,close panel lid then turn on mains power ,bobs your uncle,you should see a green and red led flash from side to side ,hope this helps

gts
March 2016
OK thanks for your advice. Which bell box would you suggest for this alarm panel

Shauki
March 2016
css connolly security systems good company in glasgow i know paul

gts
March 2016
buy a new bell box mate

gts
March 2016
Mend Security Systems, Home Alarm Systems
Mend repair fix Scantronic 9651 home alarm systems

Other models...

Scantronic 4600Scantronic 9200Scantronic 9427Scantronic 9448Scantronic 9450Scantronic 9454Scantronic 9500Scantronic 9600Scantronic 9751Scantronic 9752Scantronic 9800Scantronic 9827Scantronic 9930

How to mend ...

Find out how to mend just about anything howtomendit.com for free repair help, information and advice.

Mend home alarm systems ...

Mend Security Systems, Home Alarm Systems

Optima plus2?

have a optima plus 2 alarm had a power cut alarm now is showing zone 1 flashing but keypad is not working b... [Read more]
Mend Security Systems, Home Alarm Systems

Thorn tc3800 house alarm?

How to fix bf fault
Mend Security Systems, Home Alarm Systems

Cooper Scantronic 9448 alarm?

Have a Cooper Scantronic alarm system . Instruction book say 9448+ but front of small control box by entry is ... [Read more]
Mend Security Systems, Home Alarm Systems

Missing key Logic 4?

Hello my mother passed away and i am unable to find the Logic 4 alarm key. I dont know the key number so i am... [Read more]
Mend Security Systems, Home Alarm Systems

Yale alarm app requires password/login?

I have a Yale IA-320 alarm system and use the Yale app on my Android phone. The app periodically requires you... [Read more]
Mend Home Alarm Systems
Mend Security Systems, Home Alarm Systems
Mend repair fix Scantronic 9651 home alarm systems