when i try and enter in the code for y renault clio standard radio, all it does is beep, i have tried using keys 1-4 to enter the four diit code and also used the remote wheel on the steering wheel but i just cant get any numbers to appear to enter in the code
the radio won't turn on, battery was flat, jump started it and now no lights come on at all on the radio.
How can I leave it on for 12 hours if I don't know if it is on or off!!! Please help!!!
jacko
December 2010
i dont remember my code ,,what do i do ????
renault clio 1.2 factory radio,,any ideas
wayne
September 2010
My renault clio (Y-reg 1.2) manual says that if you enter the code incorrectly, you should wait for one minute (with the set switched on) and it will reset itself, allowing you to re-enter the code. if you enter it incorrectly again, you will need to wait for 2 minutes, then 4, 8, 16 up to 32.
If you know the code this shouldn't be a problem.
Jamie
July 2010
i no the code and typed it in and dont no how to enter it into the system is it the (as) if so what is the (as)
tom
May 2010
hi i have the same question as sam i have my radio code but when radio is connected fully there is no display and it only beeps. i know the display works fine as it works on the cassett. i am goin to try to connect it and leave it on 4 the 12 hrs but will this flatten my battery?
rachel
April 2010
I cant get the display to work on my dashboard for my clio stereo so i cant enter the code to get it working any 1 got any ideas to help
nikki
November 2009
It still looks as though you bought a faulty radio as the fuse wanting replacing....and hopefully you have the correct code?....So if you have definitely left it switched on for 12 hours (UNDISTURBED) and it still doesn`t work , then it looks as though it will have to be taken in to a Decode + Repair Specialist who will open it up to check + repair it if necessary....then recode it for you using electronic equipment. I would think that this will be very expensive so it might be cheaper to buy a used replacement (off Ebay. ?)
RegWorts
May 2008
i have tried leaving the radio on but still no change, the radio displays code, solidly with no flashing and the time which is flashing, have completely removed the battery and the radio and the same happens, all i can get the radio to do is beep when any button is pressed or the spin wheel is moved
sam
May 2008
You`ve still not said whether you have carried out the previous instructions ( leaving switched on overnight s)..If you don`t want to try that then you will have to take it in to a specialist (or buy a replacement with a code)...
It appears to me that the radio is faulty and will not work anyway because fuses don`t normally blow without a reason.
RegWorts
May 2008
well i bought the car from a dealer without the code and it didnt work before because i think a fuse had gone, i replaced the fuse and then the code problem started, got the code from a website which i had to pay for so i assume the code is right but i still cant get any digits to come onto the screen for me to enter the code, this is the same before and after
sam
May 2008
i know the code (it isnt 0000, but a 4 digit code) since i turned the radio on, after taking the battery out multiple times as i am performing numerous changes to the engine, i cant get any digits to come up on the screen for me to select the right ones, and everytime i press 1-4 for the corresponding digits i only hear a beep and even when using the remote on the steering wheel i still only hear a beep, is it possible that one of the wires controlling the radio isnt connected or, that the display is faulty and not showing the digits at all?
sam
May 2008
Did the radio work OK BEFORE you disconnected battery/worked on engine?...If so, then it looks as though the radio is locked due to too many wrong codes or wrong procedure...Re-read +carry out the advice in the previous answer (leave switched on overnight?) and hopefully it will reset automatically. You have to be patient (+ methodical) when dealing with these code problems otherwise the radio will remain locked.
RegWorts
May 2008
i know the code (it isnt 0000, but a 4 digit code) since i turned the radio on, after taking the battery out multiple times as i am performing numerous changes to the engine, i cant get any digits to come up on the screen for me to select the right ones, and everytime i press 1-4 for the corresponding digits i only hear a beep and even when using the remote on the steering wheel i still only hear a beep, is it possible that one of the wires controlling the radio isnt connected or, that the display is faulty and not showing the digits at all?
sam
May 2008
If you are sure you have the right code and you are entering it correctly http://www.davidsonelectronics.co.uk/code_entry.htm ......... then it sounds as though you have entered more than one wrong code and the radio is locked . If so , you have to switch the radio ON by pressing the appropriate button ( AS?) + the ON button. At this point you should hear a beep......Now leave the radio switched ON ( undisturbed) until it resets itself. (Possibly up to 11 hours).At this stage enter the code and press the appropriate button again ( AS ? ) and it should work
RegWorts
May 2008
Automatic Answer
While you wait for answers, we may have found some information which could help you.
howtomendit.com for free repair help, information and advice.
